最新发布第23页
排序
Fanuc Servo Resonance and Notch Filter Setup: Finding the Frequency with Servo Guide
A squealing servo is not fixed by just lowering the gain. Based on the official FANUC servo tuning manual and the HRV filter notice: separating resonance from mechanical impact, re...
机床打表找正怎么做?检具选择、标准流程、五项常见几何误差的调整部位与「检验 ≠ 找正」分层
「打表」是装配与维修现场用百分表把几何关系调回去的活,和按 ISO 230-1 出验收报告不是一回事。本页写清检具量程、预压归零、锁紧后复检,并点破网上「七项几何误差 + 垫片厚度」其实出自某一...
Machine Geometric Accuracy Check and Adjustment Framework: ISO 230-1 vs ISO 230-2, Error Families, Instruments, Tolerance Provenance and Adjustment Locations
Circulating 'geometric accuracy tolerance tables' cite the wrong standard part, present one machine-specific seven-item list as universal, and publish contradictory allowable value...
Spindle Runout: Four-Layer Diagnosis, the Two-Point Test Arbor Split and Taper Contact Pattern Checking
Runout guides publish a single universal tolerance and diagnose every far-point reading as a bearing preload problem. The two-point reading only gives a direction, and published so...
主轴跳动太大怎么调?四层排查(轴承预紧 / 锥孔接触率 / 刀柄夹紧 / 联轴器同轴度)+ 两点法分流判据与判据来源纪律
中文侧「主轴跳动」文章高度同构又互抄,径向跳动判据有的写 0.001 mm、有的写 0.005 mm,两点法「远端大」的归因在中外资料里甚至相反。本页按四层拆开,把两种解释并列写清,判据一律按机型精...
840D sl Safety Integrated Alarms 27097 / 27801 / 27810 / 27350 — SPL Start, Safe Mode Mismatch, F_DP Communication (with Machine Data)
How to diagnose SINUMERIK 840D sl Safety Integrated alarms 27097 (SPL not started), 27801/27810 (safe operating mode vs PLC config mismatch), and 27350/27351 (F_DP communication er...
Heidenhain TNC “Guard Doors Are Open” Alarm: Four-Layer Safety-Chain Isolation and the Four Post-Change Tests
When a Heidenhain TNC reports 'guard doors are open' / 'DOOR OPEN' / 'GUARD NOT CLOSED', the root cause is not faulty NC software - the PLC has evaluated the door-closed condition ...
840D sl 安全集成报警 27097/27801/27810/27350 怎么查:SPL 启动、安全模式、F_DP 通信与对应机床数据
840D sl 的 SINUMERIK Safety Integrated 报警 27097(SPL 启动未执行)、27801/27810(安全模式与 PLC 配置不一致)、27350/27351(F_DP 通信错误)怎么查。逐一对应机床数据 MD28082/28083/11...
海德汉 TNC「防护门未关 / 门未关」报警怎么查:安全链四层定位 + 门开关门锁排查 + 改动后四项验证
海德汉 TNC 报「防护门未关 / DOOR OPEN / GUARD NOT CLOSED」,本质不是 NC 软件故障,而是 PLC 把「门关闭条件」判成 false。本文按安全链四层(门开关机械 → 安全继电器 → PLC 数字量输入 ...
FANUC 急停回路怎么查?*ESP / G8.4 / X8.4 信号链 + 24V 安全链 + 主接触器 MCC 与「复位了还是没就绪」的定位顺序
急停复位了伺服还是没就绪,先别拆按钮。按 FANUC 0i 连接手册口径拆开四层链:24V 安全链、X8.4、G8.4(*ESP)、SA 与 MCC / CX4,附按 X 位状态分支的分诊表与安全红线。












































