精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第25页
西门子 828D 模拟主轴 / 模拟轴怎么配置:MD30100–31050 参数组 + X252 接线 + MD32250/32260 量程标定-CNCShare | 数控电气技术中心

西门子 828D 模拟主轴 / 模拟轴怎么配置:MD30100–31050 参数组 + X252 接线 + MD32250/32260 量程标定

828D 接变频器 / 模拟驱动时,要把轴配成「模拟轴(模拟量给定输出)」而不是数字轴。本文给出 MD30100 / 30110 / 30120 / 30130 / 30134 与 MD30200 / 30220 / 30230 / 30240 的取值口径,X252...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
04514
How to Configure an Analog Spindle / Analog Axis on SINUMERIK 828D: MD30100–31050, X252 Wiring, MD32250/32260 Scaling-CNCShare | 数控电气技术中心

How to Configure an Analog Spindle / Analog Axis on SINUMERIK 828D: MD30100–31050, X252 Wiring, MD32250/32260 Scaling

When an 828D drives an inverter or analog drive, the axis must be configured as an analog (analog setpoint output) axis rather than a digital one. This guide gives the values for M...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
04910
海德汉 TNC「防护门未关 / 门未关」报警怎么查:安全链四层定位 + 门开关门锁排查 + 改动后四项验证-CNCShare | 数控电气技术中心

海德汉 TNC「防护门未关 / 门未关」报警怎么查:安全链四层定位 + 门开关门锁排查 + 改动后四项验证

海德汉 TNC 报「防护门未关 / DOOR OPEN / GUARD NOT CLOSED」,本质不是 NC 软件故障,而是 PLC 把「门关闭条件」判成 false。本文按安全链四层(门开关机械 → 安全继电器 → PLC 数字量输入 ...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
05612
Heidenhain TNC "Guard Doors Are Open" Alarm: Four-Layer Safety-Chain Isolation and the Four Post-Change Tests-CNCShare | 数控电气技术中心

Heidenhain TNC “Guard Doors Are Open” Alarm: Four-Layer Safety-Chain Isolation and the Four Post-Change Tests

When a Heidenhain TNC reports 'guard doors are open' / 'DOOR OPEN' / 'GUARD NOT CLOSED', the root cause is not faulty NC software - the PLC has evaluated the door-closed condition ...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0339
828D 换伺服电机 / 编码器后怎么恢复:MD34210 调整状态机 + MD34090 参考点偏移 + 增量三阶段回零-CNCShare | 数控电气技术中心

828D 换伺服电机 / 编码器后怎么恢复:MD34210 调整状态机 + MD34090 参考点偏移 + 增量三阶段回零

828D 换完伺服电机或编码器,轴上电后往往报 25022「轴编码器警告 0」或直接要重新回零——丢的不是程序,而是「编码器零点与机床零点之间的对应关系」。本文按官方 Function Manual 给出增量式...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
0495
SINUMERIK 828D After a Servo-Motor / Encoder Swap: MD34210 State Machine, MD34090 Offset, Three-Phase Referencing-CNCShare | 数控电气技术中心

SINUMERIK 828D After a Servo-Motor / Encoder Swap: MD34210 State Machine, MD34090 Offset, Three-Phase Referencing

After swapping a servo motor or encoder on an 828D, the axis often comes up with alarm 25022 'Axis Encoder Warning 0' or demands referencing again. What was lost is the corresponde...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
09410
FANUC 参数表和梯形图怎么导出/打印:一键全备份、BOOT SRAM 备份、单项穿孔输出与 PMC 梯形图存卡-CNCShare | 数控电气技术中心

FANUC 参数表和梯形图怎么导出/打印:一键全备份、BOOT SRAM 备份、单项穿孔输出与 PMC 梯形图存卡

FANUC 备份分三条路:0i-F / 0i-F Plus 的一键全备份必须走两段并断电重启一次;BOOT 画面下的 SRAM 备份先于 NC 启动、不受报警影响、可整块恢复;单项数据走各自画面的 PUNCH→EXEC,每次只输...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare4天前
013112
How to Export / Print FANUC Parameter Tables and Ladder Programs: One-Click Backup, BOOT SRAM Backup and PMC Ladder to Card-CNCShare | 数控电气技术中心

How to Export / Print FANUC Parameter Tables and Ladder Programs: One-Click Backup, BOOT SRAM Backup and PMC Ladder to Card

FANUC backup has three routes: the 0i-F / 0i-F Plus one-click full backup runs in two stages and needs one power cycle; the BOOT-screen SRAM backup starts before the NC, needs no p...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
0935
828D 设定数据 SD 和机床数据 MD 到底差在哪:号段规则、激活类型、访问等级与改错后的后果-CNCShare | 数控电气技术中心

828D 设定数据 SD 和机床数据 MD 到底差在哪:号段规则、激活类型、访问等级与改错后的后果

828D 里 MD 与 SD 都存在 SRAM,但作用完全不同:MD 定义这台机器本身的物理与功能配置,改错会报警甚至撞机;SD 是操作员日常可调的运行参数,改动即时生效、风险低。本文给出官方功能手册的数...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare4天前
07214
Setting Data (SD) vs Machine Data (MD) on SINUMERIK 828D: Number Ranges, Activation Types and Access Levels-CNCShare | 数控电气技术中心

Setting Data (SD) vs Machine Data (MD) on SINUMERIK 828D: Number Ranges, Activation Types and Access Levels

On the 828D both MD and SD live in SRAM but do completely different jobs: MD defines what this machine physically is, and getting it wrong means alarms or even a crash; SD is the o...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
06611