精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第25页
FANUC 高速高精度 / 平滑控制跨机型对照表:AICC、纳米平滑、G05.1 Q1 与官方手册可核实的参数-CNCShare | 数控电气技术中心

FANUC 高速高精度 / 平滑控制跨机型对照表:AICC、纳米平滑、G05.1 Q1 与官方手册可核实的参数

一页查清 AICC / AI 纳米轮廓控制的叫法、G05.1 Q1/Q0 指令格式、官方手册可核实的参数(7066、19520、1620/1622 等)与跨机型确认方法。网传的「AICC 参数号全表」来源互相矛盾,本表逐条标明...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare14天前
0579
数控机床电气柜继电器全面解析:功能、原理、选型及应用实拍-CNCShare | 数控电气技术中心

数控机床电气柜继电器全面解析:功能、原理、选型及应用实拍

本文全面解析数控机床电气柜内继电器的核心功能、工作原理,分享针对性选型技巧,搭配实际应用实拍图,助力CNC从业者解决设备运维与电气设计问题。
发那科FANUC系统SYS_ALM015 FPU-ZERO DIVIDE EXCEPTION黑屏报警原因分析与维修方案-CNCShare | 数控电气技术中心

发那科FANUC系统SYS_ALM015 FPU-ZERO DIVIDE EXCEPTION黑屏报警原因分析与维修方案

发那科FANUC数控系统出现SYS_ALM015 FPU-ZERO DIVIDE EXCEPTION报警怎么办?本文详细解析该CPU卡硬件级故障的触发原因、排查思路与维修步骤,帮助维修工程师快速定位问题并安全恢复系统运行。
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare22天前
01469
FANUC PMC Scan Time: Why Inputs Get Missed and Timers Fire Early-CNCShare | 数控电气技术中心

FANUC PMC Scan Time: Why Inputs Get Missed and Timers Fire Early

Buttons that sometimes do nothing, a proximity contact that flickers, timers firing early - these intermittent faults almost always trace to the PMC scan cycle. This guide explains...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
0649
Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes-CNCShare | 数控电气技术中心

Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes

Split the table by A06B series, then use plain 8/9/A overcurrent versus dotted 8./9./A. IPM to decide between testing the motor cable and opening the drive.
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare11天前
0509
FANUC 对刀仪 / 测头怎么标定?5015–5018 四个接触面 + G31 / G36 / G37 + O9000 宏程序链-CNCShare | 数控电气技术中心

FANUC 对刀仪 / 测头怎么标定?5015–5018 四个接触面 + G31 / G36 / G37 + O9000 宏程序链

5015 与 5016 不是内径刀与外径刀,官方手册写的是 X 轴正负两个接触面。本页按官方附加手册讲清 5015–5018 四个基准距离、标定六步、G31 宏变量与参数号的分层、G36/G37 分工,以及宏程序编号...
FANUC Alarm Code List: P/S Alarms 0001–0224 Explained (Part 1)-CNCShare | 数控电气技术中心

FANUC Alarm Code List: P/S Alarms 0001–0224 Explained (Part 1)

English reference for FANUC P/S alarm numbers 0001 to 0224, grouped by range: tape/format errors, G code and feed, circular interpolation, tool compensation, macro errors, PMC axis...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare22天前
0719
Spindle Unclamp Failure / Tool Not Seated: Air Supply, PMC Inputs and Signal Chain-CNCShare | 数控电气技术中心

Spindle Unclamp Failure / Tool Not Seated: Air Supply, PMC Inputs and Signal Chain

Do not strip the drawbar first. Trace the eight-stage chain from the pressure switch through PMC inputs, ladder conditions, solenoid outputs and seat confirmation, then check ISO 8...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
0629
Fanuc Boot System and System Software Recovery: Main Menu, F-ROM vs S-RAM, and the 368 / 369 Alarm Mix-Up-CNCShare | 数控电气技术中心

Fanuc Boot System and System Software Recovery: Main Menu, F-ROM vs S-RAM, and the 368 / 369 Alarm Mix-Up

Reinstalling a Fanuc control is two different jobs: SYSTEM DATA LOADING writes system software into F-ROM, while SRAM DATA UTILITY restores parameters and programs into S-RAM. Circ...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0389
HEIDENHAIN iTNC 530 Manuals: NC Software Numbers versus Document IDs, the TNCguide Help System and FCL Function Limits-CNCShare | 数控电气技术中心

HEIDENHAIN iTNC 530 Manuals: NC Software Numbers versus Document IDs, the TNCguide Help System and FCL Function Limits

Forum posts pair '340 49x-05' and '606 42x-04' with individual manual titles as if one number were one book. They are NC software version numbers; each software family ships a whol...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
0619