精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第20页
FANUC PMC Data Table, Counter, Timer and Keep Relay Quick Reference: The Four PMCPRM Screens-CNCShare | 数控电气技术中心

FANUC PMC Data Table, Counter, Timer and Keep Relay Quick Reference: The Four PMCPRM Screens

T, C, K and D are PMC parameters maintained on the TIMER, COUNTR, KEEPRL and DATA screens under PMCPRM. Verifiable screen roles, byte structure evidence for T and C, reserved areas...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
07314
发那科梯形图符号速查:常开常闭、线圈、边沿与比较指令图解-CNCShare | 数控电气技术中心

发那科梯形图符号速查:常开常闭、线圈、边沿与比较指令图解

一句话答案:认错一个 FANUC 梯形图符号,程序意思就完全反过来——符号图解必须靠眼睛看。本文把最常用符号逐个画出:常开/常闭、四种线圈(普通/置位/复位/取反)、边沿检测、比较指令、跳转...
Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers-CNCShare | 数控电气技术中心

Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers

On a Fanuc PMC, addresses from R9000 upward are a system-reserved block you can read but must never write. This article explains why it is not a normal relay, gives a four-category...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare9天前
0729
828D 用户报警位地址速查:DB1600 顺序算法(700000–700247 / 701000–701999 扩展)-CNCShare | 数控电气技术中心

828D 用户报警位地址速查:DB1600 顺序算法(700000–700247 / 701000–701999 扩展)

SINUMERIK 828D 用户报警位地址速查:DB1600 顺序算法与 840D DB2 分组算法的逐项对照(700247 在 828D 是 DB1600.DBX30.7,在 840D 是 DB2.DBX201.7),248 条标准报警全表推算法,701000–701...
What Is a Fanuc PMC? Ladder Logic, Addresses and Scan Time-CNCShare | 数控电气技术中心

What Is a Fanuc PMC? Ladder Logic, Addresses and Scan Time

What is a PMC in Fanuc, and how does scan time decide ladder timing?
FANUC Inertia Ratio: Hand Calculation, Parameter 2021, Servo Guide and AI Servo Tuning-CNCShare | 数控电气技术中心

FANUC Inertia Ratio: Hand Calculation, Parameter 2021, Servo Guide and AI Servo Tuning

How to calculate and measure FANUC inertia ratio: hand formulas J=Mr² and J=M(P/2π)², parameter 2021 (default 128) and the velocity-gain conversion, Servo Guide / AI Servo Tunin...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
07210
FANUC ATC Alarms 1010–1024 — Why They Are Not in the Fanuc Manual, and How to Trace Them-CNCShare | 数控电气技术中心

FANUC ATC Alarms 1010–1024 — Why They Are Not in the Fanuc Manual, and How to Trace Them

Why tool changer / ATC alarms 1010–1024 cannot be found in any Fanuc manual: they are machine-tool-builder external alarms driven by PMC A addresses. This guide covers the alarm n...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
07210
How to Troubleshoot I/O Link & PROFIBUS Station Dropout: Reading ER97 + the I/O Link Chain Rule + PROFIBUS BF LED Diagnosis + Terminator/Address/Shielding Checklist-CNCShare | 数控电气技术中心

How to Troubleshoot I/O Link & PROFIBUS Station Dropout: Reading ER97 + the I/O Link Chain Rule + PROFIBUS BF LED Diagnosis + Terminator/Address/Shielding Checklist

Do not swap modules the moment a station drops. FANUC I/O Link is a daisy chain: one break takes out everything downstream, so the station named in the alarm is usually not the fau...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare10天前
07210
SINUMERIK 828D Common Machine Data (MD) Quick Reference — Axis / Spindle / Referencing / Soft Limits-CNCShare | 数控电气技术中心

SINUMERIK 828D Common Machine Data (MD) Quick Reference — Axis / Spindle / Referencing / Soft Limits

The machine data (MD) most often changed when commissioning a SINUMERIK 828D, grouped by function: axis setup 32100/31020/31030/31040/31050/31060, velocity/acceleration/jerk 32000/...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
07215
华中数控 HNC 报警代码速查表:真实系统报警只有 13 条(01h–44h),网传「E001–E239」是自编号-CNCShare | 数控电气技术中心

华中数控 HNC 报警代码速查表:真实系统报警只有 13 条(01h–44h),网传「E001–E239」是自编号

查华中报警前先纠正一个数:官方系统内部硬件报警只有 13 条,不是网上写的 14 条,全部 h 结尾(01h–44h)。本页逐条核实 13 条的含义、系统状态与处理措施,点破网传 E001–E239 的三处自相...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
07212