精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第19页
FANUC Alarm Code List: P/S Alarms 0492–1308 Explained (Part 3)-CNCShare | 数控电气技术中心

FANUC Alarm Code List: P/S Alarms 0492–1308 Explained (Part 3)

English reference for FANUC P/S alarm numbers 0492 to 1308: 3D interference check, Cs contour control, thread cutting, macro syntax and variables, program registration, and G10 par...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
0257
伺服放大器坏了修还是换?一张决策表和四个成本项,别只看报价单-CNCShare | 数控电气技术中心

伺服放大器坏了修还是换?一张决策表和四个成本项,别只看报价单

伺服放大器故障后只对比维修费和换新价是错的。本文给出可修性判断、维修三个层次、更换三种选择,以及含停机成本的完整决策表,帮你算出真正的成本边界。
FANUC Program Transfer: RS-232, Memory Card, USB, Ethernet and DNC — Pinout, Parameters and Troubleshooting-CNCShare | 数控电气技术中心

FANUC Program Transfer: RS-232, Memory Card, USB, Ethernet and DNC — Pinout, Parameters and Troubleshooting

Transferring a program into a FANUC control fails for four recurring reasons: wrong cable pinout, wrong 0020 I/O channel, mismatched serial frame settings, or a media format the co...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0795
Setting Data (SD) vs Machine Data (MD) on SINUMERIK 828D: Number Ranges, Activation Types and Access Levels-CNCShare | 数控电气技术中心

Setting Data (SD) vs Machine Data (MD) on SINUMERIK 828D: Number Ranges, Activation Types and Access Levels

On the 828D both MD and SD live in SRAM but do completely different jobs: MD defines what this machine physically is, and getting it wrong means alarms or even a crash; SD is the o...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
06611
FANUC Spindle Gear Shifting: 3705/3732/3735/3741-3744/3751-3753/4056-4059 and PMC Signals-CNCShare | 数控电气技术中心

FANUC Spindle Gear Shifting: 3705/3732/3735/3741-3744/3751-3753/4056-4059 and PMC Signals

Gear-shift setup breaks most often because the clamp-speed parameter names are confused (there is no 3734; minimum is 3735, maximum 3736), 3741-3744 is inverted against the gear ra...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
0516
FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查-CNCShare | 数控电气技术中心

FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查

间歇故障复现不了,只能靠「什么时候报的」串证据。本文按 FANUC 官方维修手册给出 3106#4 OPH、3106#7 OHS、3122 时标间隔与外部操作消息历史的位定义、操作履历画面调出路径,纠正网上把 #4/#...
Mitsubishi M80 Z60 / Z67 / Z68 / Z14: Fieldbus, CC-Link and CC-Link IE Field-CNCShare | 数控电气技术中心

Mitsubishi M80 Z60 / Z67 / Z68 / Z14: Fieldbus, CC-Link and CC-Link IE Field

Z60 belongs to the FCU8-WN563 fieldbus, Z67/Z68 to CC-Link, and Z14 to the CC-Link IE Field hardware test. Read n1-n4, SW0080-0083 and the official terminating resistor values befo...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare10天前
04212
CNC 24 V / 5 V Control Power Faults: SV0434 and 230041 Official Definitions, the PS0003 Number Conflict, and No-Load / Load Separation-CNCShare | 数控电气技术中心

CNC 24 V / 5 V Control Power Faults: SV0434 and 230041 Official Definitions, the PS0003 Number Conflict, and No-Load / Load Separation

A widely copied checklist presents PS0003, SV0434 and 230041 as one fault with three brand codes and publishes a voltage table as if it were official. PS0003 has two conflicting pu...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0356
SINUMERIK 840D sl to S7-1500: NCVAR Selector, PROFINET Names and Alarm 150202-CNCShare | 数控电气技术中心

SINUMERIK 840D sl to S7-1500: NCVAR Selector, PROFINET Names and Alarm 150202

A healthy PROFINET link does not give the PLC direct access to SINUMERIK machine data. This guide separates Siemens-confirmed facts from the version-dependent field workflow: Selec...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare4天前
0418
828D / 840D sl 伺服报警 25000 / 25010 / 25201 怎么分层?先看 NC 报警还是 F 码-CNCShare | 数控电气技术中心

828D / 840D sl 伺服报警 25000 / 25010 / 25201 怎么分层?先看 NC 报警还是 F 码

SINUMERIK 三码分层:25000/25010 是 NC 侧测量系统报警,25201 是 NC 转报 SINAMICS 驱动故障、真因在驱动侧 F 码。含一眼分诊表、25201 正确入口、按发生时机分诊、进给轴 vs 主轴差异,以及...