精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第8页
FANUC SV0401 报警怎么处理?SV0401/SV0416/SV0430 完整对照与排查-CNCShare | 数控电气技术中心

FANUC SV0401 报警怎么处理?SV0401/SV0416/SV0430 完整对照与排查

FANUC SV0401 SERVO ALARM VRDY OFF 完整排查:VRDY 信号断在哪四环、放大器 LED 字母码怎么反推根因、SV0416 编码器电池带电更换、SV0430 为何机械优先、报警复位后复现的三个隐藏原因。
FANUC Alarm Code List: P/S Alarms 2032–5110 Explained (Part 5)-CNCShare | 数控电气技术中心

FANUC Alarm Code List: P/S Alarms 2032–5110 Explained (Part 5)

English reference for FANUC P/S alarm numbers 2032 to 5110: Ethernet and data server errors, P-CODE macros, peripheral axis control, sheet-metal and punch-press cycles, nibbling, a...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare22天前
0658
FANUC 反向间隙补偿 1851 怎么设?千分表实测 → 检测单位换算 → 写入 → 双向验证的完整流程-CNCShare | 数控电气技术中心

FANUC 反向间隙补偿 1851 怎么设?千分表实测 → 检测单位换算 → 写入 → 双向验证的完整流程

FANUC 反向间隙补偿 1851 完整流程:千分表实测(切削 G01 与快速 G00 各一次)、检测单位换算表(0.020mm→20、车床 X 轴×2、英寸机床)、1851/1852 与 1800#4/1817#2 参数落位、PWE 写入与断...
FANUC Program Transfer Tool V18: Ethernet Setup and Program Transfer-CNCShare | 数控电气技术中心

FANUC Program Transfer Tool V18: Ethernet Setup and Program Transfer

How to install FANUC Program Transfer Tool V18 and move part programs over Ethernet: supported controls, IP planning, CNC-side FOCAS2 settings, session setup and the drag-and-drop ...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare22天前
07812
Fanuc Tool Change Stuck: 4 Manual Fixes for a Jammed ATC Arm-CNCShare | 数控电气技术中心

Fanuc Tool Change Stuck: 4 Manual Fixes for a Jammed ATC Arm

Recovery actions for an already-jammed tool change, not a diagnostic procedure. Locate the jam among six possible points, then escalate by intervention depth: PMC force output (sta...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
06110
FANUC Serial Spindle Alarms 749/750/751: Split by Timing, then DGN 409 and Amp Display-CNCShare | 数控电气技术中心

FANUC Serial Spindle Alarms 749/750/751: Split by Timing, then DGN 409 and Amp Display

749, 750 and 751 are all serial communication alarms between the CNC and the spindle amplifier - not motor faults. 750 is a failed power-on handshake, 749 a dropped link after read...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
0638
三菱 M80 PLC 编程软件用哪个?GX Works3 / GX Developer 官方下载路径 + 版本对应表 + 安装与连机常见坑-CNCShare | 数控电气技术中心

三菱 M80 PLC 编程软件用哪个?GX Works3 / GX Developer 官方下载路径 + 版本对应表 + 安装与连机常见坑

先分清「CNC 内置 PLC」和「外置 MELSEC PLC」,再选软件。三菱官方 M800/M80《PLC 开发说明书》(IB-1501270)写明的用户 PLC 开发环境是 MELSOFT 的 GX Developer;GX Works3 官网标明对应 ME...
SINUMERIK 840D sl Alarm Code Quick Reference: Number Ranges, Reactions and Manual Index-CNCShare | 数控电气技术中心

SINUMERIK 840D sl Alarm Code Quick Reference: Number Ranges, Reactions and Manual Index

840D sl alarms are six-digit numbers; the full per-number text lives only in the official Siemens diagnostics manual. This page gives the number ranges, CN/EN reaction terms, how t...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
05015
Machine Safety Circuits: STO vs SS1, Stop Categories, PL / SIL, Dual Channels and EDM-CNCShare | 数控电气技术中心

Machine Safety Circuits: STO vs SS1, Stop Categories, PL / SIL, Dual Channels and EDM

A circulating brief attributes Cat0 / Cat1 / Cat2 / Cat3 to ISO 13849. That merges two different meanings of category: stop categories 0/1/2 come from IEC 60204-1, architecture cat...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare3天前
0579
SINUMERIK 828D G290 vs G291: DIN and ISO Mode Side by Side-CNCShare | 数控电气技术中心

SINUMERIK 828D G290 vs G291: DIN and ISO Mode Side by Side

Siemens' own manual says G290 activates the Siemens NC programming language and G291 activates the ISO dialect. Each must stand alone in an NC block and the two languages cannot be...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
0555