精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第6页
看懂PMC,其实没那么难-CNCShare | 数控电气技术中心

看懂PMC,其实没那么难

《看懂PMC程序,其实没那么难》电子书高清PDF,图解急停、润滑、四轴、倍率控制及报警文本,配套PMC仿真软件,适合数控维修与调试人员从零读懂梯形图。售价100元,付款后本页立即下载。
FANUC PMC 维修学习资料-CNCShare | 数控电气技术中心

FANUC PMC 维修学习资料

Complete FANUC PMC Ladder Programming Manual & Guide. Learn FANUC PMC programming, LADDER III software installation, address table (X/Y/G/F), and troubleshooting. Download PDF manu...
FANUC Alarm History and Operation History: Using 3106#4 OPH to Trace Intermittent Faults-CNCShare | 数控电气技术中心

FANUC Alarm History and Operation History: Using 3106#4 OPH to Trace Intermittent Faults

Intermittent faults cannot be reproduced on demand, so the only evidence is the timeline. Based on the official FANUC maintenance manual, this guide covers 3106#4 OPH, 3106#7 OHS, ...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
03512
SINUMERIK 840D sl Alarm List: NCK, Cycle, HMI, SINAMICS and PLC Number Ranges-CNCShare | 数控电气技术中心

SINUMERIK 840D sl Alarm List: NCK, Cycle, HMI, SINAMICS and PLC Number Ranges

840D sl alarms use six digits. Identify the official range first, then read the cancel criterion before cycling power. Corrects two widespread range misreadings.
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
05811
Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers-CNCShare | 数控电气技术中心

Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers

The manual calls it F30020, a 828D screen shows 230020 - one fault, two numbering systems. This table maps SINAMICS F codes to 828D/840D sl display numbers, fault meanings and firs...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
04010
SINUMERIK Drive Faults Explained: F30020, F30021, F30011, F07011 and A30010 — the 230xxx Mapping, r0949 Fault Values and First Checks-CNCShare | 数控电气技术中心

SINUMERIK Drive Faults Explained: F30020, F30021, F30011, F07011 and A30010 — the 230xxx Mapping, r0949 Fault Values and First Checks

The 828D shows 230020 but the manual says F30020 - one fault, two numbering systems. This guide explains how to translate display numbers back to the manual, locate the alarm famil...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
06013
海德汉光栅尺报警排查:跟随误差超标、坐标突跳、尺寸漂移三类故障的逐段诊断-CNCShare | 数控电气技术中心

海德汉光栅尺报警排查:跟随误差超标、坐标突跳、尺寸漂移三类故障的逐段诊断

海德汉光栅尺报警逐段诊断教程:跟随误差超标、坐标突跳、尺寸漂移三类现象分向定位,按尺面与读数头、电缆与接头、供电、接地与屏蔽四段依次排除,含信号幅值判读基准与劣化基线、官方清洁规范...
FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查-CNCShare | 数控电气技术中心

FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查

间歇故障复现不了,只能靠「什么时候报的」串证据。本文按 FANUC 官方维修手册给出 3106#4 OPH、3106#7 OHS、3122 时标间隔与外部操作消息历史的位定义、操作履历画面调出路径,纠正网上把 #4/#...
SINUMERIK 828D 报警号分段速查表:000000–799999 分段规则与「这条报警该找谁」判定表-CNCShare | 数控电气技术中心

SINUMERIK 828D 报警号分段速查表:000000–799999 分段规则与「这条报警该找谁」判定表

828D 报警号不是随机数字:000000–199999 是 NC/HMI,200000–299999 是 SINAMICS,300000–399999 是驱动 I/O,400000–699999 是 PLC,700000+ 是机床厂自定义。本文给出完整分段表、三步判...
SINAMICS F 码怎么查?828D 上的 230020 到底是 F30020 —— F30001 / F30011 / F30021 / F07011 / A30010 逐条对照 + r0949 故障值读法 + 首选检查动作-CNCShare | 数控电气技术中心

SINAMICS F 码怎么查?828D 上的 230020 到底是 F30020 —— F30001 / F30011 / F30021 / F07011 / A30010 逐条对照 + r0949 故障值读法 + 首选检查动作

828D 屏上报 230020,手册里却是 F30020——同一故障两套编号。本页讲清怎么从屏幕显示号回到手册、四族报警先定位、F30020/F30021/F30011/F07011/A30010 逐条排错、r0949 故障值如何决定查线还...