SINUMERIK Servo Alarms 25000, 25010 and 25201: Which Layer to Troubleshoot First

When an 828D or 840D sl throws 25000, 25010 or 25201, the instinct is to "clear the alarm" or swap the servo motor. These three codes actually sit at different layers: 25000 and 25010 are NCK-side measuring-system alarms, while 25201 is the NC relaying a drive-side fault – the real cause lives in SINAMICS. This article gives the one-glance split, the correct entry point for 25201 and a timing-based triage that is often faster than code-based triage. Exact alarm text and remedies are subject to the diagnostics manual for your control version.

Sister article: 828D / 840D sl Servo Alarms 25000 / 25010 / 25201: Layered Troubleshooting (Chinese); related: SINUMERIK Drive Faults: F30020, F30021, F30011, F07011, Sinumerik F-Code Cross-Reference, SINUMERIK 840D sl Alarm Code Quick Reference, FANUC Alarm History and Operation History.

22.1 Three codes, three layers: one-glance triage

Three alarm layers

Table 1 25000 / 25010 / 25201 at a glance (plain text per your manual)

AlarmLayerTypical wording (official/manual sources)First place to look
25000NCK – measuring system“Axis %1 hardware fault of active encoder”Encoder / cable / DRIVE-CLiQ of the selected measuring system
25010NCK – measuring system“contamination of encoder” / measuring-system signal qualityScale, reading head, wipers, coolant ingress
25201NC relaying a drive fault“measuring circuit error” / “drive fault reported by the drive”SINAMICS drive-side F code and fault object
广告

Key sentence: 25000 and 25010 are the NC complaining about its feedback; 25201 is the NC saying “the drive reported a fault” – go read the drive, not the NC alarm list.

22.2 ★ The correct entry point for 25201

25201 correct entry point

This is the core value of the article: do not hunt for the root cause in the NC alarm text of 25201. The useful information is one layer down:

  1. In SINUMERIK Operate, open the drive diagnostics / alarms for the axis named in 25201;
  2. Read the SINAMICS-side F code (e.g. an F3xxx on the drive) and the fault object (which drive, which sensor module);
  3. Follow that F code – see drive fault codes F30020 / F30021 / F30011 and the F-code cross-reference;
  4. Only after the drive fault is cleared does 25201 disappear on the NC side.

Reports differ slightly on 25201’s plain text (“encoder measuring circuit error” in one source, “drive fault relayed to NC” in another), but both point to the drive layer – that is the robust takeaway. 300000-band drive alarms often accompany it on 840D sl.

22.3 The three checks for 25000

25000 = a hardware fault of the currently active encoder (measuring system 1 or 2, chosen by machine data). Check in this order:

  1. Encoder cable and connector at the motor and at the cabinet entry – pushed pins, moisture, coolant, loose latch; flex the cable in the drag chain while watching the position display;
  2. DRIVE-CLiQ connection on the drive side – seating and topology;
  3. Encoder / reading head itself – only after wiring is proven good. Note the alarm may name the active vs passive encoder differently (25000 active, 25001 passive on some systems).

Table 2 25000 three-check order (per your diagnostics manual)

22.4 Three field root causes for 25010

25010 = contamination of the measuring system / degraded signal quality. Typical physical causes:

  • Scale contamination or damaged reading head – dirt or oil on the scale, worn encoder disc;
  • Coolant ingress – along the scale body and cable path, the most common cause on machine tools;
  • Failed wiper / guard – the seal that should keep swarf and coolant off the scale.

This is the SINAMICS-side equivalent of the scale fault family covered for HEIDENHAIN encoders on this site; the physical diagnosis (clean, reseal, then replace) is the same – cross-check against your own manual.

22.5 Triage by “when it happens” – often faster than by code

Timing-based triage

Table 3 Triage by alarm timing

广告
When it appearsMost likely familyFirst check
On power-up, axis never movesWiring / configurationEncoder selection (MD302xx), cable, sensor module
As soon as the axis enablesParameters / enable chainEnable signals, drive ready, encoder type setting
Intermittently while runningInterference / poor contact / heatDrag-chain cable, shielding, connectors
Only at a certain positionTravel-relatedDrag-chain wear, cable bend radius, scale segment

Combined with the code layer (22.1), timing narrows the fault far faster than chasing one alarm number.

22.6 Feed axis versus spindle

25201 on a feed axis usually points to that axis’s drive and its encoder. On a spindle, the path differs: the spindle encoder and orientation / tool-position signals are involved, so check the spindle sensor module and the tool-change position feedback path as well. Do not apply the feed-axis checklist verbatim to the spindle.

22.7 ⚠️ Do not “clear the alarm” as a repair

Do not clear as a repair

Resetting an alarm does not remove the fault. Before clearing, capture the full alarm history (and the drive fault buffer) – the first alarm in the chain is often the informative one, while the alarm you see on screen may be a downstream follower such as a limit-switch alarm. See alarm and operation history tracing for the method. Repeated 25201 that “goes away after reset” is a fault to investigate, not a nuisance to ignore.

Frequently Asked Questions

What does 25201 mean on an 828D, and where is the root cause found?

25201 is the NC relaying “this axis’s drive has a fault” – the real cause is on the SINAMICS side. The correct entry point is the drive diagnostics: read that axis’s F code and fault object, rather than hunting in the NC alarm text.

What is the difference between 25000 and 25010? Are both encoder-related?

25000 is a hardware fault of the currently active encoder (check encoder, cable, DRIVE-CLiQ); 25010 is measuring-system contamination or poor signal quality (check scale, reading head, coolant ingress). Both are NCK measuring-system alarms, but the root causes differ.

A servo alarm is intermittent and clears after reset – can production continue?

No. A reset clears the display, not the fault. Capture the full alarm history and drive fault buffer first (the first alarm in the chain is often the real cause), triage by when it happens, and only then resume.

Last updated: 2026-11-19

Where to go next

Read the guide, get the right instrument, or walk the diagnosis through with someone — pick whichever you need.

© 版权声明
THE END
喜欢就支持一下吧
点赞13赞赏 分享
评论 抢沙发

请登录后发表评论

    暂无评论内容

CNC电气调试问题解答 | 数控机床电气工程师资料共享屋
CNC电气调试问题解答 | 数控机床电气工程师资料共享屋
CNC电气调试问题解答 | 数控机床电气工程师资料共享屋
CNC电气调试问题解答 | 数控机床电气工程师资料共享屋
CNC电气调试问题解答 | 数控机床电气工程师资料共享屋
CNC电气调试问题解答 | 数控机床电气工程师资料共享屋
图片-CNCShare | 数控电气技术中心
图片-CNCShare | 数控电气技术中心
图片-CNCShare | 数控电气技术中心
图片-CNCShare | 数控电气技术中心
图片-CNCShare | 数控电气技术中心
图片-CNCShare | 数控电气技术中心
SINUMERIK Servo Alarms 25000, 25010 and 25201: Which Layer to Troubleshoot First-CNCShare | 数控电气技术中心
828D / 840D sl 伺服报警 25000 / 25010 / 25201 怎么分层?先看 NC 报警还是 F 码-CNCShare | 数控电气技术中心
Mitsubishi MT Works2 / MR Configurator2: Official Download Path, Modules and Servo Parameters-CNCShare | 数控电气技术中心
三菱 MT Works2 / MR Configurator2 哪里下载?伺服调参上位机三大模块、怎么连 MR-J4/J5、能改哪些参数与三大下载坑-CNCShare | 数控电气技术中心
SINUMERIK 828D Tool Management NC-PLC Interface Explained: DB4300, Three Tables and the Drum-Magazine Wrong-Tool Case-CNCShare | 数控电气技术中心
SINUMERIK 828D 刀具管理 NC-PLC 接口详解:DB4300 任务/应答 + 三张表 + 换刀步骤与圆盘刀库取错刀号复盘-CNCShare | 数控电气技术中心
SINUMERIK 828D / 840D sl Tool Management DB Quick Reference: DB4300 Bits, DB9900/9901/9902 Tables and Transfer/Ack Steps-CNCShare | 数控电气技术中心
SINUMERIK 828D / 840D sl 刀具管理 DB 接口速查表:DB4300 位域 × DB9900/9901/9902 三表 × 传输/应答步骤号-CNCShare | 数控电气技术中心
FANUC M98 / M99 Subprogram Calls: P Numbers, Nesting Limits and How to Troubleshoot Alarms 076 / 077 / 078-CNCShare | 数控电气技术中心
FANUC M98 / M99 子程序怎么调用?P 号规则、嵌套上限与 076 / 077 / 078 三个报警怎么查-CNCShare | 数控电气技术中心
Inductive Proximity Switches for CNC Machines: NPN vs PNP vs NAMUR and Their Roles as Hard Limits, Reference Switches and Tool Presence Sensors-CNCShare | 数控电气技术中心
接近开关 NPN / PNP / NAMUR 到底怎么选怎么接?机床三大角色(硬限位 / 原点 / 刀位检测)的不同选法 + 常闭优先的失效安全 + 误动作四查-CNCShare | 数控电气技术中心
文章精选
专心做好一件事
打造更优雅的WordPress主题-CNCShare | 数控电气技术中心
专心做好一件事
打造更优雅的WordPress主题