最新发布第27页
排序
FANUC PMC 与第三方 PLC 通讯怎么实现?S7-200 与组态屏信号交换实操
发那科梯形图实操:讲清 FANUC PMC 与第三方 PLC 互联的三条信号通路(硬接线 I/O、I/O Link 总线、串口 HMI)、电气隔离与共地要点、地址对照表约定,以及信号不通的五步排查顺序
FANUC Alarm Code List: P/S Alarms 0492–1308 Explained (Part 3)
English reference for FANUC P/S alarm numbers 0492 to 1308: 3D interference check, Cs contour control, thread cutting, macro syntax and variables, program registration, and G10 par...
伺服放大器坏了修还是换?一张决策表和四个成本项,别只看报价单
伺服放大器故障后只对比维修费和换新价是错的。本文给出可修性判断、维修三个层次、更换三种选择,以及含停机成本的完整决策表,帮你算出真正的成本边界。
FANUC Program Transfer: RS-232, Memory Card, USB, Ethernet and DNC — Pinout, Parameters and Troubleshooting
Transferring a program into a FANUC control fails for four recurring reasons: wrong cable pinout, wrong 0020 I/O channel, mismatched serial frame settings, or a media format the co...
Setting Data (SD) vs Machine Data (MD) on SINUMERIK 828D: Number Ranges, Activation Types and Access Levels
On the 828D both MD and SD live in SRAM but do completely different jobs: MD defines what this machine physically is, and getting it wrong means alarms or even a crash; SD is the o...
FANUC Spindle Gear Shifting: 3705/3732/3735/3741-3744/3751-3753/4056-4059 and PMC Signals
Gear-shift setup breaks most often because the clamp-speed parameter names are confused (there is no 3734; minimum is 3735, maximum 3736), 3741-3744 is inverted against the gear ra...
FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查
间歇故障复现不了,只能靠「什么时候报的」串证据。本文按 FANUC 官方维修手册给出 3106#4 OPH、3106#7 OHS、3122 时标间隔与外部操作消息历史的位定义、操作履历画面调出路径,纠正网上把 #4/#...
Mitsubishi M80 Z60 / Z67 / Z68 / Z14: Fieldbus, CC-Link and CC-Link IE Field
Z60 belongs to the FCU8-WN563 fieldbus, Z67/Z68 to CC-Link, and Z14 to the CC-Link IE Field hardware test. Read n1-n4, SW0080-0083 and the official terminating resistor values befo...
CNC 24 V / 5 V Control Power Faults: SV0434 and 230041 Official Definitions, the PS0003 Number Conflict, and No-Load / Load Separation
A widely copied checklist presents PS0003, SV0434 and 230041 as one fault with three brand codes and publishes a voltage table as if it were official. PS0003 has two conflicting pu...
SINUMERIK 840D sl to S7-1500: NCVAR Selector, PROFINET Names and Alarm 150202
A healthy PROFINET link does not give the PLC direct access to SINUMERIK machine data. This guide separates Siemens-confirmed facts from the version-dependent field workflow: Selec...












































