最新发布第26页
排序
FANUC 换刀卡死怎么强制解开?机械手卡死 / 刀套不落位的四种手动恢复法(PMC 强制输出、电磁阀强给 24V、机械泄压、电机盘车)
换刀已经卡死时的救援动作,不是排查流程。先按六个断点分型定位,再按侵入深度从浅到深依次上手段:PMC 强制输出(普通 FORCE 需停 PMC,X/Y 自锁强制 OVERRIDE 不用停)→ 电磁阀脱离 PLC 直...
Fanuc Tool Change Stuck: 4 Manual Fixes for a Jammed ATC Arm
Recovery actions for an already-jammed tool change, not a diagnostic procedure. Locate the jam among six possible points, then escalate by intervention depth: PMC force output (sta...
FANUC 参数怎么全部清零?RESET + DELETE 上电全清 + IPL 菜单逐项实操(顺带纠正一个流传很广的错误)
网上流传的「FANUC 恢复出厂设置」教程至少有一半是错的:0i-MD / 0i-MF 根本没有这个菜单项,真正的入口是断电后按住 RESET + DELETE 上电。本文区分四种「清」(RESET+DELETE / RESET / DELET...
How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why “Restore Factory Settings” Does Not Exist)
A good half of the 'Fanuc restore factory settings' tutorials are wrong: there is no such menu on a 0i-MD / 0i-MF. The real entry is a hardware key combo - power down, hold RESET +...
FANUC PMC R9000 系列特殊继电器全表:系统保留地址含义 + 常 ON/OFF 与周期脉冲的实战用法
FANUC PMC 的 R9000 以上地址是系统保留区,只能读、不能写。本文讲清它为什么不能当普通继电器用,给出 R9091.0 常ON / R9091.1 常OFF / R9091.5·6 周期脉冲(±8ms 误差)/ R9000 运算结果位...
Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers
On a Fanuc PMC, addresses from R9000 upward are a system-reserved block you can read but must never write. This article explains why it is not a normal relay, gives a four-category...
FANUC 刀具寿命管理(TM)怎么开?8132#0 / 13203#7 / 6800 / 6813 参数 + G10 L3 编程 + F64.0 报警接线全流程
FANUC 刀具寿命管理(TM)把同型刀编成组、预设寿命、自动计数与换刀。本文按 0i-D/0i-F 核对 8132#0 开户、6813 最大组数、6800 组数×刀数、6800#2 次数/时间、13203#7 计数触发、6810 忽略号...
How to Set Up Fanuc Tool Life Management (TM): 8132#0 / 13203#7 / 6800 / 6813 Parameters + G10 L3 Programming + F64.0 Alarm Wiring
Fanuc Tool Life Management (TM) groups interchangeable tools, gives each group a life limit and counts down automatically. This guide covers enabling with 8132#0, max groups 6813 (...
数控机床电气原理图怎么看?符号/线号/主回路/控制回路/PMC 地址反查一图读懂
从符号、线号、页次到主回路、控制回路,再到 PMC 地址怎么对应回图纸上的那根线——手把手教你把一张数控机床电气原理图读明白,并顺着报警号反查故障点。
How to Read a CNC Machine Electrical Schematic – Symbols, Wire Numbers, Power/Control Circuits, and Tracing an Alarm via PMC Address
A practical method for reading any CNC electrical schematic - common symbols and designations, wire/sheet numbers as coordinates, how to read the power and control circuits, and ho...












































