最新发布第18页
排序
CNC Alarm Message Chinese Reference: 120 Common English Phrases and a 30-Second Triage Method
Translating an English alarm is only the first step. This page groups 120 common field phrasings by subsystem with Chinese meanings, maps keywords such as NOT READY, OVERLOAD, FAUL...
数控机床英文报警中文对照(120 条句式样例)+ 看到英文报警后 30 秒定位该查哪个点
现场常见英文报警大多是机床厂写在 PMC/PLC 的自定义文本。本页按 12 个子系统给出 120 条英文句式样例与中文含义,再用 NOT READY / OVERLOAD / FAULT / TIMEOUT / LOW / INTERLOCK 判读触发语...
How to Export / Print FANUC Parameter Tables and Ladder Programs: One-Click Backup, BOOT SRAM Backup and PMC Ladder to Card
FANUC backup has three routes: the 0i-F / 0i-F Plus one-click full backup runs in two stages and needs one power cycle; the BOOT-screen SRAM backup starts before the NC, needs no p...
“FANUC Data Backup and Recovery: ALL I/O Full Backup vs BOOT SRAM Backup — 3 Methods Compared + Restore Steps”
'FANUC data backup explained: when to use ALL I/O one-click full backup (0i-F / 0i-F Plus), BOOT SRAM backup (system won't boot), or itemized backup. Covers parameters 0020 / 0313#...
Refurbished vs New FANUC Servo Amplifier: Cost Comparison and Repair-or-Replace Decision Table
Comparing repair cost against new-part cost is the wrong way to decide. This guide covers repairability assessment, three tiers of repair, three replacement options, and a four-fac...
Fanuc CNC Specifications Comparison: 0i-MF vs 30i-B vs 31i-B vs 32i-B vs 35i-B, Two Official Data Sets
Is the 30i-B a 96-axis or a 40-axis control? Both figures are official, from two generations of Fanuc literature. Two data sets side by side, a fourteen-item verification framework...
GSK CNC Alarm Code Reference: 980T / 980TD / 988T / 988TA Number Ranges and PLC Alarms 1000-1037 with A-Addresses
Search results for GSK alarm codes are dominated by English sites. This page verifies the framework against the GSK988T User Manual Appendix A.8 and the 980TDb standard ladder: 980...
Fanuc Alarm, Parameter and Diagnostic Cross-Reference Table: Verified SV / PS / OH Anchors and the Two Numbering Generations
You have a Fanuc alarm number - what next? This page turns the three-way mapping of alarm number, parameter number and diagnostic number into a framework table: the alarm is the sy...
Fanuc 0i-B / 0i-C Legacy Alarms: Same Number, Different Board – 920 / 930 / 950 / 974 / 975 Decoded
On a 0i-B or 0i-C the alarms are plain numbers with no SV/PS prefix, and a 920 does not point to the same hardware as on a 0i-D/0i-F. The 900 range verified against manual B-64115E...
FANUC 数据备份与恢复完整教程:ALL I/O 全备份 / BOOT SRAM 备份 三套方法对比与恢复实操
FANUC 数据备份三套方法怎么选:ALL I/O 一键全备份(0020/0313#0/0138#0,断电重启后自动补输出 SRAM 与用户文件)、BOOT 画面 SRAM 备份(SRAM_BAK.001,系统起不来时唯一可用手段)、分项备...










































