精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第16页
SINUMERIK 828D to S7-1200/1500: PN/PN Coupler Cyclic I/O vs S7 GET/PUT-CNCShare | 数控电气技术中心

SINUMERIK 828D to S7-1200/1500: PN/PN Coupler Cyclic I/O vs S7 GET/PUT

A PN/PN Coupler exchanges data through PROFINET cyclic I/O mapping; S7 GET/PUT uses a one-sided S7 connection. Official configuration order, X1/X2 network split, MD12986, byte-exte...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare4天前
0577
828D 设定数据 SD 和机床数据 MD 到底差在哪:号段规则、激活类型、访问等级与改错后的后果-CNCShare | 数控电气技术中心

828D 设定数据 SD 和机床数据 MD 到底差在哪:号段规则、激活类型、访问等级与改错后的后果

828D 里 MD 与 SD 都存在 SRAM,但作用完全不同:MD 定义这台机器本身的物理与功能配置,改错会报警甚至撞机;SD 是操作员日常可调的运行参数,改动即时生效、风险低。本文给出官方功能手册的数...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare4天前
07214
FANUC PMC 与第三方 PLC 通讯怎么实现?S7-200 与组态屏信号交换实操-CNCShare | 数控电气技术中心

FANUC PMC 与第三方 PLC 通讯怎么实现?S7-200 与组态屏信号交换实操

发那科梯形图实操:讲清 FANUC PMC 与第三方 PLC 互联的三条信号通路(硬接线 I/O、I/O Link 总线、串口 HMI)、电气隔离与共地要点、地址对照表约定,以及信号不通的五步排查顺序
SINUMERIK 828D G290 G291 怎么切?DIN 写法与 ISO 写法逐行对照-CNCShare | 数控电气技术中心

SINUMERIK 828D G290 G291 怎么切?DIN 写法与 ISO 写法逐行对照

G290 激活西门子 NC 编程语言,G291 激活 ISO 方言;两者必须单独成段,同段禁止混写。本页给出程序头、换刀、主轴、轮廓、循环的逐行对照,并用西门子官方手册纠正“模式可互相识别”的真正含...
SINUMERIK 840D sl 与 S7-1500 怎么通讯?PROFINET 设备名 + NCVAR Selector 从 PLC 读写 MD 全流程-CNCShare | 数控电气技术中心

SINUMERIK 840D sl 与 S7-1500 怎么通讯?PROFINET 设备名 + NCVAR Selector 从 PLC 读写 MD 全流程

MD 存在 840D sl 的 NC 内核里,不在 PLC 的 DB 中。本页按官方边界与现场流程分开讲:PROFINET 设备名、NCVAR Selector 六步、TIA Portal 限制、150202 的真实含义与四类备份。第三方块名与错...
SINUMERIK 828D G290 vs G291: DIN and ISO Mode Side by Side-CNCShare | 数控电气技术中心

SINUMERIK 828D G290 vs G291: DIN and ISO Mode Side by Side

Siemens' own manual says G290 activates the Siemens NC programming language and G291 activates the ISO dialect. Each must stand alone in an NC block and the two languages cannot be...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare4天前
0545
SINUMERIK 840D sl to S7-1500: NCVAR Selector, PROFINET Names and Alarm 150202-CNCShare | 数控电气技术中心

SINUMERIK 840D sl to S7-1500: NCVAR Selector, PROFINET Names and Alarm 150202

A healthy PROFINET link does not give the PLC direct access to SINUMERIK machine data. This guide separates Siemens-confirmed facts from the version-dependent field workflow: Selec...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare4天前
0418
FANUC Main Board Spare Numbers: A16B / A17B / A20B Board Families and 5 Things to Check Before Swapping-CNCShare | 数控电气技术中心

FANUC Main Board Spare Numbers: A16B / A17B / A20B Board Families and 5 Things to Check Before Swapping

Circulated tables like 'A20B-8100-0135 = 0i-A, -0450 = 0i-B, -0660 = 0i-C' come from different spare vendors who conflict with each other. Labeled as circulated field lists to veri...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
05211
FANUC ATC Alarms 1010–1024 — Why They Are Not in the Fanuc Manual, and How to Trace Them-CNCShare | 数控电气技术中心

FANUC ATC Alarms 1010–1024 — Why They Are Not in the Fanuc Manual, and How to Trace Them

Why tool changer / ATC alarms 1010–1024 cannot be found in any Fanuc manual: they are machine-tool-builder external alarms driven by PMC A addresses. This guide covers the alarm n...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
07210
Fanuc 0i-MD PMC Diagnostic Screens: PMCDGN, STATUS, LAD and PARAM-CNCShare | 数控电气技术中心

Fanuc 0i-MD PMC Diagnostic Screens: PMCDGN, STATUS, LAD and PARAM

What PMCDGN, STATUS, LAD and PARAM each answer on a Fanuc 0i-MD.