最新发布第34页
排序
SINUMERIK Servo Alarms 25000, 25010 and 25201: Which Layer to Troubleshoot First
SINUMERIK three-code triage: 25000/25010 are NCK measuring-system alarms, while 25201 is the NC relaying a SINAMICS drive fault whose real cause is a drive-side F code. Includes a ...
CNC 报警号形态识别卡:FANUC / SINUMERIK / 三菱 M80 / HEIDENHAIN 位数、前缀与号段对照(30 秒定位该翻哪本手册)
看到一个报警号,先判断它是哪个系统的。本页只做入口识别:四品牌报警号的位数、前缀与号段形态、该去哪个画面查、翻哪本手册、站内哪篇速查页对得上,附 6 位号分流法。
发那科梯形图保持型地址:哪些断电不丢 R DR E EP
一句话答案:发那科 PMC 地址并非一律断电就丢:R(保持型继电器)是主力,DR/E/EP 也属保持型,而 K/D/A 容易与 R 混淆;分清地址的断电保持特性才能避免「重启就出问题」的隐蔽故障。本文讲清...
SINUMERIK 840D sl 报警代码一览表:NCK / 循环 / HMI / SINAMICS / PLC 五区号段
840D sl 报警是六位号。按官方诊断手册号段定归属,再读清除条件决定要不要断电;纠正「4xxxx = 机床数据」与「700000 归西门子」两处误读。
FANUC PMC Functional Instruction (SUB) Quick Reference: Numbers, Families and Model Availability
PMC functional instructions are called by SUB number, but the same SUB number is not available on every PMC model. Verifiable SUB numbers and families from official Table 5(a), rea...
Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check
A parameter listed in the manual but absent on the control is usually not lost. Option entitlement versus visibility, axis-count filtering, generation differences, write protection...
Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes
Split the table by A06B series, then use plain 8/9/A overcurrent versus dotted 8./9./A. IPM to decide between testing the motor cable and opening the drive.
828D 电池报警 2100/2101/2102 怎么处理?带电换还是断电换、哪些数据会丢、风扇电池模块怎么拔
828D 电池报警 2100/2101/2102 完整处置:三级电压阈值(预警 2.7-2.9V/报警 2.4-2.6V)与处置窗口、缓冲电容 30 分钟带电换不丢数据、2102 数据丢失逐项清单、风扇与电池同模块的风险与双模块...
海德汉 TNC 基本程序段速查表:BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/CYCL DEF 一页对照
把海德汉 TNC 最常用的对话式程序段压成一页:程序结构 8 步、常用段全表、走刀要素(R0/RL/RR、DR、I)、常用 M 代码。现场写程序或读别人程序时对着查。
FANUC 换刀卡死怎么强制解开?机械手卡死 / 刀套不落位的四种手动恢复法(PMC 强制输出、电磁阀强给 24V、机械泄压、电机盘车)
换刀已经卡死时的救援动作,不是排查流程。先按六个断点分型定位,再按侵入深度从浅到深依次上手段:PMC 强制输出(普通 FORCE 需停 PMC,X/Y 自锁强制 OVERRIDE 不用停)→ 电磁阀脱离 PLC 直...












































