精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第34页
FANUC Alarm Code List: P/S Alarms 5130–5559 Explained (Part 6)-CNCShare | 数控电气技术中心

FANUC Alarm Code List: P/S Alarms 5130–5559 Explained (Part 6)

English reference for FANUC P/S alarm numbers 5130 to 5559: PMC axis overlap, flexible synchronous control, tool management and interference, Cs contour control, tilted surface mac...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
0515
How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why "Restore Factory Settings" Does Not Exist)-CNCShare | 数控电气技术中心

How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why “Restore Factory Settings” Does Not Exist)

A good half of the 'Fanuc restore factory settings' tutorials are wrong: there is no such menu on a 0i-MD / 0i-MF. The real entry is a hardware key combo - power down, hold RESET +...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0516
发那科梯形图保持型地址:哪些断电不丢 R DR E EP-CNCShare | 数控电气技术中心

发那科梯形图保持型地址:哪些断电不丢 R DR E EP

一句话答案:发那科 PMC 地址并非一律断电就丢:R(保持型继电器)是主力,DR/E/EP 也属保持型,而 K/D/A 容易与 R 混淆;分清地址的断电保持特性才能避免「重启就出问题」的隐蔽故障。本文讲清...
SINUMERIK 840D sl 报警代码一览表:NCK / 循环 / HMI / SINAMICS / PLC 五区号段-CNCShare | 数控电气技术中心

SINUMERIK 840D sl 报警代码一览表:NCK / 循环 / HMI / SINAMICS / PLC 五区号段

840D sl 报警是六位号。按官方诊断手册号段定归属,再读清除条件决定要不要断电;纠正「4xxxx = 机床数据」与「700000 归西门子」两处误读。
FANUC PMC Functional Instruction (SUB) Quick Reference: Numbers, Families and Model Availability-CNCShare | 数控电气技术中心

FANUC PMC Functional Instruction (SUB) Quick Reference: Numbers, Families and Model Availability

PMC functional instructions are called by SUB number, but the same SUB number is not available on every PMC model. Verifiable SUB numbers and families from official Table 5(a), rea...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
05014
Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check-CNCShare | 数控电气技术中心

Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check

A parameter listed in the manual but absent on the control is usually not lost. Option entitlement versus visibility, axis-count filtering, generation differences, write protection...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0508
Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes-CNCShare | 数控电气技术中心

Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes

Split the table by A06B series, then use plain 8/9/A overcurrent versus dotted 8./9./A. IPM to decide between testing the motor cable and opening the drive.
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare10天前
0509
828D 电池报警 2100/2101/2102 怎么处理?带电换还是断电换、哪些数据会丢、风扇电池模块怎么拔-CNCShare | 数控电气技术中心

828D 电池报警 2100/2101/2102 怎么处理?带电换还是断电换、哪些数据会丢、风扇电池模块怎么拔

828D 电池报警 2100/2101/2102 完整处置:三级电压阈值(预警 2.7-2.9V/报警 2.4-2.6V)与处置窗口、缓冲电容 30 分钟带电换不丢数据、2102 数据丢失逐项清单、风扇与电池同模块的风险与双模块...
海德汉 TNC 基本程序段速查表:BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/CYCL DEF 一页对照-CNCShare | 数控电气技术中心

海德汉 TNC 基本程序段速查表:BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/CYCL DEF 一页对照

把海德汉 TNC 最常用的对话式程序段压成一页:程序结构 8 步、常用段全表、走刀要素(R0/RL/RR、DR、I)、常用 M 代码。现场写程序或读别人程序时对着查。
FANUC 换刀卡死怎么强制解开?机械手卡死 / 刀套不落位的四种手动恢复法(PMC 强制输出、电磁阀强给 24V、机械泄压、电机盘车)-CNCShare | 数控电气技术中心

FANUC 换刀卡死怎么强制解开?机械手卡死 / 刀套不落位的四种手动恢复法(PMC 强制输出、电磁阀强给 24V、机械泄压、电机盘车)

换刀已经卡死时的救援动作,不是排查流程。先按六个断点分型定位,再按侵入深度从浅到深依次上手段:PMC 强制输出(普通 FORCE 需停 PMC,X/Y 自锁强制 OVERRIDE 不用停)→ 电磁阀脱离 PLC 直...