最新发布第7页
排序
FANUC 参数改不了/写不进去怎么解除?PWE 参数写入开关 + SW0100 + 3210/3211 与 3202#4 NE9 混淆纠正
参数写不进去,先分清是 PWE 没开、程序编辑被保护、9000 号程序密码锁,还是新机的 8 级保护。本文给 MDI 到 SETTING 开 PWE 的完整路径,说明 SW0100 只是状态提示,并纠正把 3210/3211、3202...
SINUMERIK 840D sl Alarm List: NCK, Cycle, HMI, SINAMICS and PLC Number Ranges
840D sl alarms use six digits. Identify the official range first, then read the cancel criterion before cycling power. Corrects two widespread range misreadings.
FANUC 参数不见了怎么查?四种隐藏机制:选件授权 / 轴数 gating / 版本差异 / 写入权限
手册里有的参数本机翻不到,多数不是丢了。本页分开讲选件授权与可见性分离、轴数与硬件配置过滤、机型版本差异、写入权限与显示过滤,并给出现场核对五步与三类禁止试探。
FANUC 主轴定向 M19 角度怎么调?参数 4077 换算公式(4096 脉冲/圈)+ 3117#1 与诊断 445/449 实操
M19 角度不对改的是 4077,但它存的是相对一转信号的偏移计数不是角度。本页给出换算式(4096 脉冲/圈、0.0879°/格、0–4095)、角度对照、3117#1 打开诊断 445/449 的标准调整路径,以及 G10 ...
Fanuc Canned Cycle Parameter Table: Address Words, Parameters 5121/5213 and Related Alarms
A citable FANUC canned-cycle reference: nine cycles x address words x parameters x alarms, four-way, with an anchor on each row. Covers the nine-cycle master table, X/Y/Z/R/Q/P/F/K...
FANUC 0I-MD系统X轴窜动故障维修实例 | 共享屋
完整拆解一台配套FANUC 0I-MD系统的卧式加工中心X轴窜动故障:从机械润滑、丝杠间隙到伺服增益、编码器信号丢波,6步排查+参数优化,最终尺寸精度恢复到±0.01 mm,附维修要点与周期保养建议。
FANUC 系统基础调试教程:硬件连接 + 参数设置 + 故障维修全解析
本文详解 FANUC(发那科)数控系统基础调试与维修全流程,涵盖 0i-MD/TD、31i-A 等主流型号的硬件连接(伺服、I/O 单元、SDU)、参数设置、PMC 编程、光栅尺反馈配置等实操步骤,同时汇总伺服报...
What Is a Fanuc PMC? Ladder Logic, Addresses and Scan Time
What is a PMC in Fanuc, and how does scan time decide ladder timing?
CNC Servo Vibration, Overshoot and Noise: A Phenomenon-Based Troubleshooting Table
Classify servo vibration into 4 types (high-frequency squeal, low-frequency flutter, start/stop overshoot, machining ripple) and follow the right branch. Covers HRV filters, inerti...
FANUC Inertia Ratio: Hand Calculation, Parameter 2021, Servo Guide and AI Servo Tuning
How to calculate and measure FANUC inertia ratio: hand formulas J=Mr² and J=M(P/2π)², parameter 2021 (default 128) and the velocity-gain conversion, Servo Guide / AI Servo Tunin...












































