最新发布第35页
排序
SINUMERIK 828D PLC Programming Tool: STEP 7 Toolbox and the FB1/FB2/OB100 Basic Program
The basic PLC program ships inside the licensed SINUMERIK STEP 7 Toolbox as master copy libraries and STL sources, matched to the NCU firmware. Three official sources, three correc...
机床精度检验怎么做?球杆仪 ISO 230-4 与激光 ISO 230-2 判据对照
球杆仪做的是圆测试(ISO 230-4),激光干涉仪做的是定位精度与重复定位(ISO 230-2 / GB-T 17421.2),两者不是一套判据。本文给出标准分工、球杆仪六步作业、官方七类误差诊断项与验收结论三...
主轴松刀失败 / 刀夹不到位怎么查?气源压力 + PMC 信号链 + 电磁阀
松刀失败别先拆打刀缸。本文把压力基准、ISO 8573-1 气源质量等级、压力开关到 PMC 输入点再到电磁阀输出的完整信号链、三种检漏手法与机械侧兜底串成一条排查路径。
Spindle Unclamp Failure / Tool Not Seated: Air Supply, PMC Inputs and Signal Chain
Do not strip the drawbar first. Trace the eight-stage chain from the pressure switch through PMC inputs, ladder conditions, solenoid outputs and seat confirmation, then check ISO 8...
三菱 M80 Z60 / Z67 / Z68 / Z14 报警怎么查?先分清三种网络
Z60 是 FCU8-WN563 的现场总线,Z67/Z68 是 CC-Link,Z14 是 CC-Link IE Field 的硬件测试——四个号不在同一条总线上。本文按官方手册口径拆解 n1–n4、断线定位、终端电阻与屏蔽接地。
Mitsubishi M80 Z60 / Z67 / Z68 / Z14: Fieldbus, CC-Link and CC-Link IE Field
Z60 belongs to the FCU8-WN563 fieldbus, Z67/Z68 to CC-Link, and Z14 to the CC-Link IE Field hardware test. Read n1-n4, SW0080-0083 and the official terminating resistor values befo...
SINUMERIK 840D sl 报警速查总表:六位号段 / 系统响应 / 官方章节索引
840D sl 报警是六位号,完整逐号文本在西门子官方报警诊断手册。本页给出号段分区、系统响应术语中英对照、官方样例行读法、清除条件与官方检索键,工单和故障报告可直接抄走框架。
SINUMERIK 840D sl Alarm Code Quick Reference: Number Ranges, Reactions and Manual Index
840D sl alarms are six-digit numbers; the full per-number text lives only in the official Siemens diagnostics manual. This page gives the number ranges, CN/EN reaction terms, how t...
FANUC 伺服报警三向对照总表:SV 号 / 放大器数码管码 / 诊断号怎么对
同一次故障常同时看到 CNC 的 SV 报警号和放大器上的数码管码,但两者没有官方通用映射表。本页给出三套编码的关系、可核实的号段与码型、诊断号交叉列的正确用法和处理动作列。
Fanuc Servo Alarm Reference Chart: CNC SV Code, Amplifier 7-Segment Code and Diagnostic Number
One fault often shows both a CNC SV alarm and an amplifier seven-segment code, but FANUC publishes no universal mapping. This page explains the three code systems, verifiable numbe...












































