最新发布第26页
排序
Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers
On a Fanuc PMC, addresses from R9000 upward are a system-reserved block you can read but must never write. This article explains why it is not a normal relay, gives a four-category...
Mitsubishi M80 Magazine Scrambled Quick Chart: Symptom, Tool Registration Fields and R Registers
One page for a scrambled Mitsubishi M80 magazine: match the symptom, then act. Spindle sync, the four Tool Registration targets, and the magazine / tool-life R-register addresses a...
HEIDENHAIN TNC Fixed Cycle Parameter Reference: Cycle 200/203/230/251/252/4xx Q Parameters and FANUC G-Cycle Migration
HEIDENHAIN TNC fixed cycle Q-parameter reference: drilling 200-209, pocket milling 230/251/252, probing 4xx, tool measurement 48x with per-cycle Q meanings. Corrects the Q212/Q213 ...
FANUC 系统基础调试教程:硬件连接 + 参数设置 + 故障维修全解析
本文详解 FANUC(发那科)数控系统基础调试与维修全流程,涵盖 0i-MD/TD、31i-A 等主流型号的硬件连接(伺服、I/O 单元、SDU)、参数设置、PMC 编程、光栅尺反馈配置等实操步骤,同时汇总伺服报...
FANUC 高速高精度 / 平滑控制跨机型对照表:AICC、纳米平滑、G05.1 Q1 与官方手册可核实的参数
一页查清 AICC / AI 纳米轮廓控制的叫法、G05.1 Q1/Q0 指令格式、官方手册可核实的参数(7066、19520、1620/1622 等)与跨机型确认方法。网传的「AICC 参数号全表」来源互相矛盾,本表逐条标明...
发那科FANUC系统SYS_ALM015 FPU-ZERO DIVIDE EXCEPTION黑屏报警原因分析与维修方案
发那科FANUC数控系统出现SYS_ALM015 FPU-ZERO DIVIDE EXCEPTION报警怎么办?本文详细解析该CPU卡硬件级故障的触发原因、排查思路与维修步骤,帮助维修工程师快速定位问题并安全恢复系统运行。
FANUC PMC Scan Time: Why Inputs Get Missed and Timers Fire Early
Buttons that sometimes do nothing, a proximity contact that flickers, timers firing early - these intermittent faults almost always trace to the PMC scan cycle. This guide explains...
Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes
Split the table by A06B series, then use plain 8/9/A overcurrent versus dotted 8./9./A. IPM to decide between testing the motor cable and opening the drive.
FANUC 对刀仪 / 测头怎么标定?5015–5018 四个接触面 + G31 / G36 / G37 + O9000 宏程序链
5015 与 5016 不是内径刀与外径刀,官方手册写的是 X 轴正负两个接触面。本页按官方附加手册讲清 5015–5018 四个基准距离、标定六步、G31 宏变量与参数号的分层、G36/G37 分工,以及宏程序编号...











































