精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第16页
SINUMERIK 828D 报警代码一览表(中文)— NC / PLC / SINAMICS F 代码三区对照与处理-CNCShare | 数控电气技术中心

SINUMERIK 828D 报警代码一览表(中文)— NC / PLC / SINAMICS F 代码三区对照与处理

SINUMERIK 828D 报警代码中文速查:NC / 轴 / 机床数据 / 700xxx / SINAMICS F 五段号段分区对照,含 2100 电池、2110 温度、2120 风扇、2130 口令、2140 维修开关等断电前必处理项,以及 F3000...
FANUC PMC Project From Scratch: The 6-Stage Flow From Backup to Download to Verification-CNCShare | 数控电气技术中心

FANUC PMC Project From Scratch: The 6-Stage Flow From Backup to Download to Verification

A complete FANUC PMC project in six stages: site survey, full backup, address planning, safety-first logic, online download, staged verification. Plus the five things to hand over ...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare11天前
04813
Used CNC Machine Electrical Inspection Checklist — 30 Checks Before You Pay the Balance-CNCShare | 数控电气技术中心

Used CNC Machine Electrical Inspection Checklist — 30 Checks Before You Pay the Balance

The most expensive mistake in a used CNC purchase is in the electrical cabinet. This 30-point field checklist covers history verification, power-off checks, live testing, and how t...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare7天前
0369
Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences-CNCShare | 数控电气技术中心

Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences

Tool measurement with a Heidenhain TT goes wrong for three recurring reasons: the cycle format does not match the control generation, the safety-zone parameter is looked for in the...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare3天前
05913
Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers-CNCShare | 数控电气技术中心

Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers

On a Fanuc PMC, addresses from R9000 upward are a system-reserved block you can read but must never write. This article explains why it is not a normal relay, gives a four-category...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare10天前
0729
Mitsubishi M80 Magazine Scrambled Quick Chart: Symptom, Tool Registration Fields and R Registers-CNCShare | 数控电气技术中心

Mitsubishi M80 Magazine Scrambled Quick Chart: Symptom, Tool Registration Fields and R Registers

One page for a scrambled Mitsubishi M80 magazine: match the symptom, then act. Spindle sync, the four Tool Registration targets, and the magazine / tool-life R-register addresses a...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
0559
FANUC 伺服共振 / 啸叫怎么抑制?陷波滤波器(频率·带宽·衰减)参数设定 + Servo Guide 扫频定位全流程-CNCShare | 数控电气技术中心

FANUC 伺服共振 / 啸叫怎么抑制?陷波滤波器(频率·带宽·衰减)参数设定 + Servo Guide 扫频定位全流程

伺服啸叫不是把增益调小一句话能解决的。本文按 FANUC 官方伺服调整手册与 HRV 滤波器通知,讲清共振、啸叫与机械撞击的分流、Servo Guide 扫频读尖峰频率、陷波滤波器三要素与多组分配,以及先...
FANUC PMC Functional Instruction (SUB) Quick Reference: Numbers, Families and Model Availability-CNCShare | 数控电气技术中心

FANUC PMC Functional Instruction (SUB) Quick Reference: Numbers, Families and Model Availability

PMC functional instructions are called by SUB number, but the same SUB number is not available on every PMC model. Verifiable SUB numbers and families from official Table 5(a), rea...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare3天前
05614
主轴跳动太大怎么调?四层排查(轴承预紧 / 锥孔接触率 / 刀柄夹紧 / 联轴器同轴度)+ 两点法分流判据与判据来源纪律-CNCShare | 数控电气技术中心

主轴跳动太大怎么调?四层排查(轴承预紧 / 锥孔接触率 / 刀柄夹紧 / 联轴器同轴度)+ 两点法分流判据与判据来源纪律

中文侧「主轴跳动」文章高度同构又互抄,径向跳动判据有的写 0.001 mm、有的写 0.005 mm,两点法「远端大」的归因在中外资料里甚至相反。本页按四层拆开,把两种解释并列写清,判据一律按机型精...
FANUC PMC 扫描周期怎么导致信号漏采、定时器提前:中文现场排查-CNCShare | 数控电气技术中心

FANUC PMC 扫描周期怎么导致信号漏采、定时器提前:中文现场排查

按钮按了有时没反应、接近开关到位触点偶尔不亮、定时器没到时间就动作——这类偶发问题多半与 PMC 扫描周期有关。本页讲清输入—执行—输出四阶段、扫描时间以本机诊断画面为准、四类典型现象...