最新发布第29页
排序
Fanuc Threading G32 / G92 / G76: Fixing Pitch Errors and Spindle Sync Problems
Thread pitch errors are rarely fixed by tweaking a tool offset. The real cause is a broken sync chain between the spindle one-rotation signal and Z-axis feed per revolution. Covers...
Fanuc System Alarms 950, 971, 974: Meaning and Board-Level Diagnosis
Fanuc system alarms 900–976 in one table: 900 ROM PARITY, 910–919 memory parity, 920/921 axis cards, 926 FSSB, 930 CPU, 935 SRAM ECC, 950/951 PMC with the PCxxx detail code, 970...
FANUC Servo Amplifier Replacement: Power-Off and Discharge, Teardown Order, Motor ID No.2020 Write-Back, Three Post-Swap Checks
A complete FANUC servo amplifier replacement procedure following official αi / βi parameter wording: the repair-or-replace decision, cutting main power (not the E-stop) and waiti...
FANUC 高速高精度 / 平滑控制跨机型对照表:AICC、纳米平滑、G05.1 Q1 与官方手册可核实的参数
一页查清 AICC / AI 纳米轮廓控制的叫法、G05.1 Q1/Q0 指令格式、官方手册可核实的参数(7066、19520、1620/1622 等)与跨机型确认方法。网传的「AICC 参数号全表」来源互相矛盾,本表逐条标明...
Spindle Runout: Four-Layer Diagnosis, the Two-Point Test Arbor Split and Taper Contact Pattern Checking
Runout guides publish a single universal tolerance and diagnose every far-point reading as a bearing preload problem. The two-point reading only gives a direction, and published so...
HEIDENHAIN TNC Conversational Programming for Beginners: One Minimal Program
HEIDENHAIN Klartext is conversational programming - the screen asks, you answer, no G-code memorising. Using a 13-line minimal program, this explains BEGIN PGM, BLK FORM blank, TOO...
Fanuc Tool Setter / Probe Calibration: Parameters 5015-5018, G31 / G36 / G37 and the O9000 Macro Chain
Parameters 5015 and 5016 are not ID and OD tools. The official Fanuc additional manual defines four contact surfaces. Four reference distances, a six-step field calibration, skip v...
HEIDENHAIN TNC Generation Cross-Reference: MP vs Cfg, Model Differences and Cycle Compatibility
One-page lookup for iTNC 530 / TNC 620 / TNC 640 / TNC7: positioning, control loops, NC software numbers, MP vs Cfg parameter systems, and the MP-to-Cfg mappings HEIDENHAIN officia...
828D 全闭环改半闭环怎么改?屏蔽光栅尺的 MD 参数 + PLC 位 + 间隙补偿三件套
SINUMERIK 828D 全闭环改半闭环完整教程:光栅尺故障应急屏蔽与永久改半闭环的三层改法——NC 机床数据(MD30200 测量系统数量、MD30230 输入分配把电机编码器排到第一路、MD31000/31010/31020/...
How to Classify and Troubleshoot CNC Homing Failures: Reference Not Found vs Wrong Reference Position + Decel Dog / One-Turn Signal + Grid Shift 1850 / Reference Counter 1821 + Absolute Encoder Battery
Stop swapping parts to see what sticks. Split homing failures into two classes: reference not found, and reference position wrong. In the first class, watch whether the axis decele...












































