精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第30页
数控机床都有哪些岗位?具体需要学习什么指示?-CNCShare | 数控电气技术中心

数控机床都有哪些岗位?具体需要学习什么指示?

一篇看懂数控机床行业完整岗位链:数控操作工、CAM编程员、工艺工程师、设备维修、售后、质量、生产管理等8大典型职位,附每岗必须掌握的课程、证书与成长路径,助你1-3年完成从新人到工程师的...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
02998
FANUC 伺服放大器 A06B 数码管报警码全表:普通码查电缆,带点码查 IPM-CNCShare | 数控电气技术中心

FANUC 伺服放大器 A06B 数码管报警码全表:普通码查电缆,带点码查 IPM

先按 A06B 型号分表(α SVU / α SVM / αi SVM),再用 8/9/A 过流与 8./9./A. IPM 的判别法决定先测电机线还是拆驱动;附断电三步与主轴两位码区分。
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare10天前
0738
Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check-CNCShare | 数控电气技术中心

Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check

A parameter listed in the manual but absent on the control is usually not lost. Option entitlement versus visibility, axis-count filtering, generation differences, write protection...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0508
FANUC PMC编程太难?学会这招,让复杂的程序变简单!-CNCShare | 数控电气技术中心

FANUC PMC编程太难?学会这招,让复杂的程序变简单!

还在为复杂的FANUC PMC梯形图头疼吗?本文用大白话讲解“步序”和“功能块”两大神器,教你如何把复杂的机床程序写得更简单、更清晰,效率翻倍!
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
02748
主轴松刀失败 / 刀夹不到位怎么查?气源压力 + PMC 信号链 + 电磁阀-CNCShare | 数控电气技术中心

主轴松刀失败 / 刀夹不到位怎么查?气源压力 + PMC 信号链 + 电磁阀

松刀失败别先拆打刀缸。本文把压力基准、ISO 8573-1 气源质量等级、压力开关到 PMC 输入点再到电磁阀输出的完整信号链、三种检漏手法与机械侧兜底串成一条排查路径。
SINUMERIK 828D Tool Management NC-PLC Interface Explained: DB4300, Three Tables and the Drum-Magazine Wrong-Tool Case-CNCShare | 数控电气技术中心

SINUMERIK 828D Tool Management NC-PLC Interface Explained: DB4300, Three Tables and the Drum-Magazine Wrong-Tool Case

Following the 828D DB quick reference, this explains the interface logic: the NCK-tool-management-to-PLC handshake, DB4300 job/command bits, the DB9900/9901/9902 table roles, 1:1 v...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
0588
SINUMERIK 828D / 840D sl vs FANUC vs Mitsubishi M80 Parameter Cross-Reference (Aligned by Function)-CNCShare | 数控电气技术中心

SINUMERIK 828D / 840D sl vs FANUC vs Mitsubishi M80 Parameter Cross-Reference (Aligned by Function)

Three-brand parameter cross-reference: 828D/840D sl, FANUC and Mitsubishi M80 aligned by function across axis, soft limits, backlash, spindle, zero points, lube, filtering and serv...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
0538
Fanuc G41/G42 Interference Alarm: The 2×TNR Minimum Radial Step Rule Explained-CNCShare | 数控电气技术中心

Fanuc G41/G42 Interference Alarm: The 2×TNR Minimum Radial Step Rule Explained

The complete FANUC G41/G42 interference alarm (PS0041 / PS0325) guide: the 2×TNR minimum radial step rule with the 0.0156 inch / 0.0092 inch worked case, the TNR matrix, five caus...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0458
如何使用LADDER III软件查看梯形图的程序的步数?-CNCShare | 数控电气技术中心

如何使用LADDER III软件查看梯形图的程序的步数?

本文详细介绍如何在FANUC LADDER III软件中查看梯形图程序的已用步数。通过简单的界面操作,帮助工程师确认PMC程序容量,避免因步数超限导致的调试问题。
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
02588
二手加工中心电气验收清单:30 项必查,别被"能转就行"骗了-CNCShare | 数控电气技术中心

二手加工中心电气验收清单:30 项必查,别被”能转就行”骗了

二手加工中心验收最容易踩的坑在电气。这份 30 项现场检查清单,从履历核对、断电检查、上电测试到隐瞒手段识别,帮你在付尾款前把问题找出来。
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0598