最新发布第3页
排序
SINUMERIK 828D External Programs / DNC: EXTCALL Syntax, Running from CF/USB, Network Online
The 828D has limited NC memory, so large mould programs are either copied in, executed from external memory, or run online over the network. This covers EXTCALL drive letters and t...
SINUMERIK 840D sl 报警代码一览表:NCK / 循环 / HMI / SINAMICS / PLC 五区号段
840D sl 报警是六位号。按官方诊断手册号段定归属,再读清除条件决定要不要断电;纠正「4xxxx = 机床数据」与「700000 归西门子」两处误读。
Fanuc Parameter Number Map by Range: Which Block Controls What
No universal 0000-9999 Fanuc parameter table exists. Chapter 4 functional block framework, verifiable landmark parameters, a change-risk grading, number-based manual lookup keys an...
Fanuc 0i-B / 0i-C Legacy Alarms: Same Number, Different Board – 920 / 930 / 950 / 974 / 975 Decoded
On a 0i-B or 0i-C the alarms are plain numbers with no SV/PS prefix, and a 920 does not point to the same hardware as on a 0i-D/0i-F. The 900 range verified against manual B-64115E...
FANUC 固定循环速查表:G73 / G81 / G82 / G83 / G84 / G85 / G86 / G87 / G88 × 地址字(X Y Z R Q P F K)× 相关参数(5121 / 5213 / 5200-5209)× 相关报警(045 / 073 / 074)
一张可直接引用的 FANUC 固定循环速查表:九个循环 × 地址字 × 参数 × 报警四向对照,每行带锚点。含九循环主表、X/Y/Z/R/Q/P/F/K 地址字全表、5121/5213/5200-5209 参数区段、045/073/074 ...
西门子840D系统轮廓误差报警解决实例|雷尼绍编码器安装调试全攻略
西门子840D数控系统轮廓误差报警维修案例详解:雷尼绍编码器安装后出现位置偏差超出允许范围故障,系统无法正常进入加工模式。通过编码器安装精度校正、信号线路优化、系统参数配置调整等三步解...
发那科梯形图:FANUC PMC 自定义报警 ALARM 写法与显示画面
一句话答案:FANUC PMC 自定义报警是机床厂家在发那科梯形图里用 ALARM 指令自行定义的中文报警提示;发那科出厂只提供框架与通道。它由 报警号、报警内容、触发条件 三部分组成,写法遵循文中...
FANUC PMC Troubleshooting: 5 Real Cases Using Signal Tracing
Master FANUC PMC troubleshooting with 5 real cases: spindle M03 no response, ATC tool-change timeout, E-stop cannot reset, lube pump timer fault, hydraulic chuck no action. Uses a ...
FANUC 伺服惯量比怎么测怎么算?手算公式 + 参数 2021 辨识 + Servo Guide 与 AI Servo Tuning 实操
FANUC 惯量比手算公式 J=Mr² 与 J=M(P/2π)²,参数 2021 负载惯量比(默认 128)与速度环增益换算表,Servo Guide / AI Servo Tuning 自动惯量估计与前后参数对比,偏差>30% 的机械故障判读,...












































