最新发布第30页
排序
HEIDENHAIN TNC Conversational Programming for Beginners: One Minimal Program
HEIDENHAIN Klartext is conversational programming - the screen asks, you answer, no G-code memorising. Using a 13-line minimal program, this explains BEGIN PGM, BLK FORM blank, TOO...
海德汉 TNC 对话式编程入门:一个最小程序看懂 BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/循环
海德汉 Klartext 对话式编程,屏幕问一句你答一句,不用背 G 代码。本文用一个 13 行能跑的最小程序,逐行讲清 BEGIN PGM、BLK FORM 毛坯、TOOL CALL 刀具、L 直线、C/CR 圆弧、R0/RL/RR 补偿、...
海德汉 TNC 基本程序段速查表:BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/CYCL DEF 一页对照
把海德汉 TNC 最常用的对话式程序段压成一页:程序结构 8 步、常用段全表、走刀要素(R0/RL/RR、DR、I)、常用 M 代码。现场写程序或读别人程序时对着查。
HEIDENHAIN TNC Block Quick Reference: BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/CYCL DEF
The most-used HEIDENHAIN TNC Klartext blocks compressed onto one page - the 8-step program layout, a full block table, motion elements (R0/RL/RR, DR, I) and common M codes. For wri...
海德汉 TNCremo / TNCcmd 传输程序:以太网 LSV2 端口 19000、连接设置、批量 TNCcmd
TNCremo 是海德汉官方图形界面传输/备份软件,TNCcmd 是它附带的命令行工具,能把'连上→建目录→put'写成批处理。本文讲清两者分工、以太网 LSV2(默认端口 19000)/RS-232/USB 三种连接、PC ...
HEIDENHAIN TNCremo / TNCcmd Program Transfer: Ethernet LSV2 Port 19000
TNCremo is HEIDENHAIN's official GUI transfer/backup software; TNCcmd is its command-line companion that turns connect-mkdir-put into a batch file. This covers the two roles, Ether...
西门子 828D 外部程序 / DNC 在线加工:EXTCALL 语法、CF/USB 直接运行、网盘在线、RS232 的边界
828D 的 NC 内存有限,大模具程序要么拷进来、要么从外部存储器直接跑、要么走网络在线加工。本文讲清 EXTCALL 的盘符与 SD42700 预设路径、U 盘/CF 卡直接运行(为什么推荐 CF 不推荐 U 盘)、...
SINUMERIK 828D External Programs / DNC: EXTCALL Syntax, Running from CF/USB, Network Online
The 828D has limited NC memory, so large mould programs are either copied in, executed from external memory, or run online over the network. This covers EXTCALL drive letters and t...
FANUC 参数改不了/写不进去怎么解除?PWE 参数写入开关 + SW0100 + 3210/3211 与 3202#4 NE9 混淆纠正
参数写不进去,先分清是 PWE 没开、程序编辑被保护、9000 号程序密码锁,还是新机的 8 级保护。本文给 MDI 到 SETTING 开 PWE 的完整路径,说明 SW0100 只是状态提示,并纠正把 3210/3211、3202...
FANUC Parameter Write Protect (PWE): How to Unlock Parameters, SW0100, and the 3210/3211 vs 3202#4 NE9 Mix-Up
Four independent locks can stop you editing a FANUC control. This guide gives the MDI to SETTING to PWE path, explains why SW0100 is only a status message, and corrects the widespr...












































