精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第41页
840D sl Safety Integrated Alarms 27097 / 27801 / 27810 / 27350 — SPL Start, Safe Mode Mismatch, F_DP Communication (with Machine Data)-CNCShare | 数控电气技术中心

840D sl Safety Integrated Alarms 27097 / 27801 / 27810 / 27350 — SPL Start, Safe Mode Mismatch, F_DP Communication (with Machine Data)

How to diagnose SINUMERIK 840D sl Safety Integrated alarms 27097 (SPL not started), 27801/27810 (safe operating mode vs PLC config mismatch), and 27350/27351 (F_DP communication er...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
04115
Fanuc Rigid Tapping Parameter Quick Reference: 5200–5294, SP0741 and DGN 452/453-CNCShare | 数控电气技术中心

Fanuc Rigid Tapping Parameter Quick Reference: 5200–5294, SP0741 and DGN 452/453

A copy-straight-to-the-machine Fanuc rigid tapping reference: 5200-5294 grouped into five blocks (enable bits, gear ratio, speed limit 5241-5244, gains and time constants, deviatio...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
0409
Fanuc 0i-B / 0i-C Legacy Alarms: Same Number, Different Board - 920 / 930 / 950 / 974 / 975 Decoded-CNCShare | 数控电气技术中心

Fanuc 0i-B / 0i-C Legacy Alarms: Same Number, Different Board – 920 / 930 / 950 / 974 / 975 Decoded

On a 0i-B or 0i-C the alarms are plain numbers with no SV/PS prefix, and a 920 does not point to the same hardware as on a 0i-D/0i-F. The 900 range verified against manual B-64115E...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
04014
HEIDENHAIN iTNC 530 vs TNC 620 / 640 / TNC7: Differences, MP vs Cfg, and Program Migration-CNCShare | 数控电气技术中心

HEIDENHAIN iTNC 530 vs TNC 620 / 640 / TNC7: Differences, MP vs Cfg, and Program Migration

iTNC 530 uses MP machine parameters while TNC 620/640/TNC7 use structured Cfg objects — the first divide in any retrofit or upgrade. This guide uses official HEIDENHAIN data for g...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
0407
Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers-CNCShare | 数控电气技术中心

Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers

The manual calls it F30020, a 828D screen shows 230020 - one fault, two numbering systems. This table maps SINAMICS F codes to 828D/840D sl display numbers, fault meanings and firs...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
04010
机床打表找正怎么做?检具选择、标准流程、五项常见几何误差的调整部位与「检验 ≠ 找正」分层-CNCShare | 数控电气技术中心

机床打表找正怎么做?检具选择、标准流程、五项常见几何误差的调整部位与「检验 ≠ 找正」分层

「打表」是装配与维修现场用百分表把几何关系调回去的活,和按 ISO 230-1 出验收报告不是一回事。本页写清检具量程、预压归零、锁紧后复检,并点破网上「七项几何误差 + 垫片厚度」其实出自某一...
Fanuc Parameter Number Map by Range: Which Block Controls What-CNCShare | 数控电气技术中心

Fanuc Parameter Number Map by Range: Which Block Controls What

No universal 0000-9999 Fanuc parameter table exists. Chapter 4 functional block framework, verifiable landmark parameters, a change-risk grading, number-based manual lookup keys an...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
0397
Fanuc M19 Spindle Orientation: Parameter 4077 Angle Formula, 3117#1 and Diagnostics 445/449-CNCShare | 数控电气技术中心

Fanuc M19 Spindle Orientation: Parameter 4077 Angle Formula, 3117#1 and Diagnostics 445/449

When M19 stops at the wrong angle, the value to change is 4077 - but it holds an offset count relative to the one-turn signal, not degrees. Verified formula (4096 counts/rev, 0.087...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
03910
FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查-CNCShare | 数控电气技术中心

FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查

间歇故障复现不了,只能靠「什么时候报的」串证据。本文按 FANUC 官方维修手册给出 3106#4 OPH、3106#7 OHS、3122 时标间隔与外部操作消息历史的位定义、操作履历画面调出路径,纠正网上把 #4/#...
SINUMERIK 828D NCK Battery Alarm 2100/2101/2102: Replace Live or Power Down?-CNCShare | 数控电气技术中心

SINUMERIK 828D NCK Battery Alarm 2100/2101/2102: Replace Live or Power Down?

The complete guide to SINUMERIK 828D NCK battery alarms 2100/2101/2102: the three voltage thresholds and their remedy windows, replacing live with the 30-minute buffer capacitor (n...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare10天前
03913