最新发布第38页
排序
FANUC 0i-F / 0i-F Plus 功能选项对照与「我这台机器到底装了什么」怎么查:规格表图例、选件族与代号纠错
手册里有 AI 轮廓控制,为什么机床上用不了?操作手册描述的是全部可选功能。本页按官方 0i-F Plus 规格表讲清「书里有不等于机器上有」、符号图例、三种查证路径,并纠正几处选件代号误传。
Fanuc 0i-F / 0i-F Plus Function Options and How to Find Out What Your Machine Actually Has
The manual lists AI contour control, so why can you not use it? An operating manual describes every optional function in the series. Symbol legends, three verification paths, optio...
SINUMERIK 828D / 840D sl 快捷键速查(官方手册核实版):六个操作区 + Ctrl / Alt 组合键 + .ARC / .ARD 版本差异
中文转载的「西门子快捷键大全」是同源稿件,把 840D sl 的 Ctrl+Alt+S 也写成 .ARD,把第六个操作区写成「系统」,还漏掉官方两条注意事项。本页按官方操作手册逐条核实,并点破官方中文版 PDF...
SINUMERIK 828D / 840D sl Shortcut Keys Verified Against the Official Manuals: Six Operating Areas, Ctrl / Alt Keys and the ARC / ARD Split
Circulating 'complete Sinumerik shortcut lists' are same-source reprints that get 840D sl Ctrl+Alt+S wrong, rename the sixth operating area and drop two official notes. Every key c...
FANUC 装系统 / 系统软件丢了怎么办?BOOT SYSTEM 主菜单逐项 + 三层存储分区 + 368/369 报警纠错
装系统是两件事:系统软件写入 F-ROM 走 SYSTEM DATA LOADING,参数与程序恢复走 SRAM DATA UTILITY。本页按 BOOT 主菜单逐项拆开,并纠正 368/369 报警的三套编号混用与机器人控制器警告的跨产...
Fanuc Boot System and System Software Recovery: Main Menu, F-ROM vs S-RAM, and the 368 / 369 Alarm Mix-Up
Reinstalling a Fanuc control is two different jobs: SYSTEM DATA LOADING writes system software into F-ROM, while SRAM DATA UTILITY restores parameters and programs into S-RAM. Circ...
数控 24V / 5V 控制电源故障怎么查?SV0434 与 230041 官方口径 + PS0003 编号冲突 + 空载负载分离法
简报把 PS0003 / SV0434 / 230041 写成三品牌同源现象,又把经验电压表当成官方判据。核实后:PS0003 存在两套互相冲突的解释,SV0434 与 230041 的检测位置和阈值完全不同。本页把官方口径与经...
CNC 24 V / 5 V Control Power Faults: SV0434 and 230041 Official Definitions, the PS0003 Number Conflict, and No-Load / Load Separation
A widely copied checklist presents PS0003, SV0434 and 230041 as one fault with three brand codes and publishes a voltage table as if it were official. PS0003 has two conflicting pu...
机床安全回路怎么接才合规?STO / SS1 与四类架构:停止类别、PL / SIL 等级、双通道与 EDM 回读
简报把 Cat0 / Cat1 / Cat2 / Cat3 写成「ISO 13849 定义」,这是把停止类别与架构类别揉成一套。本页按 IEC 60204-1、IEC 61800-5-2、ISO 13849-1 三套体系分开写,并说明为什么普通 PLC 输出...
Machine Safety Circuits: STO vs SS1, Stop Categories, PL / SIL, Dual Channels and EDM
A circulating brief attributes Cat0 / Cat1 / Cat2 / Cat3 to ISO 13849. That merges two different meanings of category: stop categories 0/1/2 come from IEC 60204-1, architecture cat...






































