最新发布第38页
排序
FANUC No-Alarm Fault Diagnosis: How to Use DGN000, DGN003, DGN005
FANUC no-alarm fault diagnosis: map hidden faults to specific diagnosis numbers. DGN000 = M-code not confirmed, DGN003 = in-position check stuck, DGN005 = axis interlock. Includes ...
Fanuc 0i-F / 0i-F Plus Function Options and How to Find Out What Your Machine Actually Has
The manual lists AI contour control, so why can you not use it? An operating manual describes every optional function in the series. Symbol legends, three verification paths, optio...
FANUC 对刀仪 / 测头怎么标定?5015–5018 四个接触面 + G31 / G36 / G37 + O9000 宏程序链
5015 与 5016 不是内径刀与外径刀,官方手册写的是 X 轴正负两个接触面。本页按官方附加手册讲清 5015–5018 四个基准距离、标定六步、G31 宏变量与参数号的分层、G36/G37 分工,以及宏程序编号...
Fanuc G41/G42 Interference Alarm: The 2×TNR Minimum Radial Step Rule Explained
The complete FANUC G41/G42 interference alarm (PS0041 / PS0325) guide: the 2×TNR minimum radial step rule with the 0.0156 inch / 0.0092 inch worked case, the TNR matrix, five caus...
FANUC Spindle Amplifier Alarm Codes 01-88 (SPM/PSM) and First Checks
Reading the two digits on the spindle amp LED? This full list maps FANUC SPM alarm codes 01–88 and A/b0/C0 letter codes to plain-English meaning, first action, and how to tell whe...
828D 第三个手轮 / Mini HHU 怎么接?MD11350 + FB1 + DB11/DB21/DB31
前两个手轮走 X143,第三个走 MCP 的 X60;828D 的 MD11350=5 与 840D sl PROFINET MCP 的 =7 不能混用。讲清三个 MD、FB1 RUN_UP 必填参数、PLC 三区信号,以及手轮转而轴不动最常见的原因。
FANUC Alarm Code List: P/S Alarms 1332–1973 Explained (Part 4)
English reference for FANUC P/S alarm numbers 1332 to 1973: 3D handle feed, normal direction control, M code duplication, index table, program security, EGB, RS-232C interface, USB...
西门子 828D 模拟主轴 / 模拟轴怎么配置:MD30100–31050 参数组 + X252 接线 + MD32250/32260 量程标定
828D 接变频器 / 模拟驱动时,要把轴配成「模拟轴(模拟量给定输出)」而不是数字轴。本文给出 MD30100 / 30110 / 30120 / 30130 / 30134 与 MD30200 / 30220 / 30230 / 30240 的取值口径,X252...
FANUC 伺服共振 / 啸叫怎么抑制?陷波滤波器(频率·带宽·衰减)参数设定 + Servo Guide 扫频定位全流程
伺服啸叫不是把增益调小一句话能解决的。本文按 FANUC 官方伺服调整手册与 HRV 滤波器通知,讲清共振、啸叫与机械撞击的分流、Servo Guide 扫频读尖峰频率、陷波滤波器三要素与多组分配,以及先...
数控机床英文报警中文对照(120 条句式样例)+ 看到英文报警后 30 秒定位该查哪个点
现场常见英文报警大多是机床厂写在 PMC/PLC 的自定义文本。本页按 12 个子系统给出 120 条英文句式样例与中文含义,再用 NOT READY / OVERLOAD / FAULT / TIMEOUT / LOW / INTERLOCK 判读触发语...






































