最新发布第32页
排序
CNC Servo Vibration, Overshoot and Noise: A Phenomenon-Based Troubleshooting Table
Classify servo vibration into 4 types (high-frequency squeal, low-frequency flutter, start/stop overshoot, machining ripple) and follow the right branch. Covers HRV filters, inerti...
How HEIDENHAIN TNC Tool Management Works – tool_p.tch Pocket Table + TOOL.T Tool Table + L/R Compensation + Tool Life
HEIDENHAIN TNC manages tools with two tables: TOOL.T holds each tool's length/radius/life, TOOL_P.TCH maps each magazine pocket to a tool. This guide explains both tables, how L/R ...
Mitsubishi M80 Tool Magazine Out-of-Order: Fix It with Tool Registration
A scrambled tool magazine on a Mitsubishi M80 is not 'a tool loaded wrong': the recorded tool number no longer matches the physical pot. Do not copy the M70 M77/M74/M79 codes - the...
三菱 M80 数据备份与恢复:MPARA 是密码不是文件,整体备份 7 项 + 单文件 ALL.PRM + 电池
M80 备份绕不开'MPARA',但它是'全部备份'画面的进入密码,不是备份文件格式。本文讲清两种备份方式(整体打包 vs 单文件)、整体备份 7 项文件清单、备份/恢复流程与三条铁律、ALL.PRM 单文件...
三菱 M80 刀库乱刀怎么修:先分真假,再用 T 登录逐位修正
三菱 M80 刀库乱刀的本质是系统记录的刀号与实际刀位对不上。不要照搬 M70 的 M77/M74/M79 维修代码,M80 的正确手段是 Setup 下的刀具登录逐位核对 + 主轴同步,再按信号/参数/机械三分法定位...
Mitsubishi M80 Magazine Scrambled Quick Chart: Symptom, Tool Registration Fields and R Registers
One page for a scrambled Mitsubishi M80 magazine: match the symptom, then act. Spindle sync, the four Tool Registration targets, and the magazine / tool-life R-register addresses a...
三菱 M80 刀库乱刀速查表:现象·原因·先查 + T 登录四个位置 + R 寄存器
一页看完三菱 M80 刀库乱刀:按现象对号入座,主轴同步、T 登录四个位置、刀库刀具数据与刀具寿命的 R 寄存器地址一次列清。适合现场贴着机台用。
Fanuc Analog Spindle Commissioning: Enable Chain 8133#5/3716#0/3717, 3730/3731 Voltage Calibration, and JA40/JA41 Wiring
An analog spindle is rarely beaten by the number of parameters. It is beaten by a wrong enable order, 3730 and 3731 swapped, or an inverted coder phase on JA41. Four stages in orde...
FANUC 模拟主轴调试全流程:8133#5/3716#0/3717 启用链 + 3730/3731 电压标定 + JA40/JA41 接线
模拟主轴的坑不在参数多,而在启用链顺序错、3730 与 3731 填反、JA41 编码器 A/B 接错。本文按接线→启用链→电压标定→功能验证四步走:给出 3717 填 0 时无报警却不转的原因、3731 先 3730 ...
FANUC Serial Spindle Alarms 749/750/751: Split by Timing, then DGN 409 and Amp Display
749, 750 and 751 are all serial communication alarms between the CNC and the spindle amplifier - not motor faults. 750 is a failed power-on handshake, 749 a dropped link after read...










































