最新发布第38页
排序
How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why “Restore Factory Settings” Does Not Exist)
A good half of the 'Fanuc restore factory settings' tutorials are wrong: there is no such menu on a 0i-MD / 0i-MF. The real entry is a hardware key combo - power down, hold RESET +...
FANUC LADDER III: Compile, Decompile and Program Protection Explained
Why FANUC LADDER III needs compile and decompile: compile to download or monitor online, decompile to edit or analyze an uploaded program. Plus how ladder program password protecti...
FANUC PMC R9000 系列特殊继电器全表:系统保留地址含义 + 常 ON/OFF 与周期脉冲的实战用法
FANUC PMC 的 R9000 以上地址是系统保留区,只能读、不能写。本文讲清它为什么不能当普通继电器用,给出 R9091.0 常ON / R9091.1 常OFF / R9091.5·6 周期脉冲(±8ms 误差)/ R9000 运算结果位...
海德汉 TNC 固定循环参数速查表:Cycle 200/203/230/251/252/256/257/4xx/48x 逐个 Q 参数含义 + 与 FANUC G 循环迁移
海德汉 TNC 固定循环 Q 参数速查:钻孔族 200-209、型腔铣 230/251/252、探测 4xx、刀具测量 48x 逐条 Q 参数含义,纠正 Q212/Q213 网上错写,附 FANUC G 循环功能迁移对照。参数按 iTNC530/TNC...
“FANUC Data Backup and Recovery: ALL I/O Full Backup vs BOOT SRAM Backup — 3 Methods Compared + Restore Steps”
'FANUC data backup explained: when to use ALL I/O one-click full backup (0i-F / 0i-F Plus), BOOT SRAM backup (system won't boot), or itemized backup. Covers parameters 0020 / 0313#...
SINUMERIK 828D / 840D sl 快捷键速查(官方手册核实版):六个操作区 + Ctrl / Alt 组合键 + .ARC / .ARD 版本差异
中文转载的「西门子快捷键大全」是同源稿件,把 840D sl 的 Ctrl+Alt+S 也写成 .ARD,把第六个操作区写成「系统」,还漏掉官方两条注意事项。本页按官方操作手册逐条核实,并点破官方中文版 PDF...
数控机床冷却 / 油路 / 排屑 / 气压 / 液压 五类报警怎么查?英文报警文本 → PMC 反馈位 → 处理动作
冷却、润滑、排屑、气压、液压五类英文报警大多不是系统报警,而是机床厂写在 PMC 里的自定义文本。本页给出五子系统横向对照:文本只是线索,真正要查的是「没就绪还是执行中受阻」,再沿报警...
SINUMERIK 828D 报警代码一览表(中文)— NC / PLC / SINAMICS F 代码三区对照与处理
SINUMERIK 828D 报警代码中文速查:NC / 轴 / 机床数据 / 700xxx / SINAMICS F 五段号段分区对照,含 2100 电池、2110 温度、2120 风扇、2130 口令、2140 维修开关等断电前必处理项,以及 F3000...
FANUC Servo Amplifier Replacement: Power-Off and Discharge, Teardown Order, Motor ID No.2020 Write-Back, Three Post-Swap Checks
A complete FANUC servo amplifier replacement procedure following official αi / βi parameter wording: the repair-or-replace decision, cutting main power (not the E-stop) and waiti...
三菱 M80 数据备份与恢复:MPARA 是密码不是文件,整体备份 7 项 + 单文件 ALL.PRM + 电池
M80 备份绕不开'MPARA',但它是'全部备份'画面的进入密码,不是备份文件格式。本文讲清两种备份方式(整体打包 vs 单文件)、整体备份 7 项文件清单、备份/恢复流程与三条铁律、ALL.PRM 单文件...





































