精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第41页
FANUC SERVO GUIDE: Waveform Analysis, Vibration Suppression and Rigid Tapping-CNCShare | 数控电气技术中心

FANUC SERVO GUIDE: Waveform Analysis, Vibration Suppression and Rigid Tapping

A field guide to FANUC SERVO GUIDE: what it does, which controls it supports, how to install and connect over Ethernet, and the four workflows that solve most servo problems.
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
0826
How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why "Restore Factory Settings" Does Not Exist)-CNCShare | 数控电气技术中心

How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why “Restore Factory Settings” Does Not Exist)

A good half of the 'Fanuc restore factory settings' tutorials are wrong: there is no such menu on a 0i-MD / 0i-MF. The real entry is a hardware key combo - power down, hold RESET +...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare7天前
0526
Mitsubishi M80 Tool Magazine Out-of-Order: Fix It with Tool Registration-CNCShare | 数控电气技术中心

Mitsubishi M80 Tool Magazine Out-of-Order: Fix It with Tool Registration

A scrambled tool magazine on a Mitsubishi M80 is not 'a tool loaded wrong': the recorded tool number no longer matches the physical pot. Do not copy the M70 M77/M74/M79 codes - the...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
03714
FANUC 车螺纹乱牙 / 螺距不对怎么查?G32/G92/G76 主轴同步链路 + 一转信号 + G96 恒线速与 G50 限速设置-CNCShare | 数控电气技术中心

FANUC 车螺纹乱牙 / 螺距不对怎么查?G32/G92/G76 主轴同步链路 + 一转信号 + G96 恒线速与 G50 限速设置

车螺纹乱牙不是改刀补能解决的,本质是主轴一转信号与 Z 轴每转进给的同步被破坏。本文按 FANUC 官方维修手册给出三类乱牙表现的分流方法、G32/G92/G76 的同步要求、SP9041/9042/9046/9047 报警...
Fanuc Servo Alarm Reference Chart: CNC SV Code, Amplifier 7-Segment Code and Diagnostic Number-CNCShare | 数控电气技术中心

Fanuc Servo Alarm Reference Chart: CNC SV Code, Amplifier 7-Segment Code and Diagnostic Number

One fault often shows both a CNC SV alarm and an amplifier seven-segment code, but FANUC publishes no universal mapping. This page explains the three code systems, verifiable numbe...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare6天前
0477
Machine Geometric Accuracy Check and Adjustment Framework: ISO 230-1 vs ISO 230-2, Error Families, Instruments, Tolerance Provenance and Adjustment Locations-CNCShare | 数控电气技术中心

Machine Geometric Accuracy Check and Adjustment Framework: ISO 230-1 vs ISO 230-2, Error Families, Instruments, Tolerance Provenance and Adjustment Locations

Circulating 'geometric accuracy tolerance tables' cite the wrong standard part, present one machine-specific seven-item list as universal, and publish contradictory allowable value...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare7天前
0328
电气原理图 ↔ I/O 分配表 ↔ PMC 梯形图三方对照:从报警反查到端子和元件的完整路径-CNCShare | 数控电气技术中心

电气原理图 ↔ I/O 分配表 ↔ PMC 梯形图三方对照:从报警反查到端子和元件的完整路径

现场最费时的故障往往是图纸、地址表和梯形图三份资料对不上。本页讲清三方的职责边界与换算关系,给出从报警文本分类、A/D 地址、梯形图触点到 I/O 端子和电气图纸的完整反查链,以及找不到触...
机床为什么要预热?热变形与首件精度漂移:三处热源 + 20 分钟预热协议 + 主轴油温与环境温度设定 + 热伸长诊断方法-CNCShare | 数控电气技术中心

机床为什么要预热?热变形与首件精度漂移:三处热源 + 20 分钟预热协议 + 主轴油温与环境温度设定 + 热伸长诊断方法

机床预热与热变形全解:三处热源地图、两个方向性判据、20 分钟分档预热协议、千分表热平衡判定、主轴油冷机低 2–3℃ 设定、软件补偿不能替代预热的边界与设备台账化。数值按本机手册与实测热...
数控机床内部电压分类解说-CNCShare | 数控电气技术中心

数控机床内部电压分类解说

共享屋提供数控机床内部电压的完整分级:从380V动力母线到3.3V板级电源,图解7大层级来源、负荷、保护及测试要点,助力电气工程师快速定位故障、安全维修。
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare22天前
020214
数控机床电气柜电抗器完全指南-CNCShare | 数控电气技术中心

数控机床电气柜电抗器完全指南

深度解析数控机床电气柜内电抗器的工作原理、选型参数计算方法,对比西门子、ABB、施耐德等主流品牌价格性能,提供谐波抑制和功率因数优化的专业解决方案,助您精准选择最适合的电抗器产品。'