最新发布第3页
排序
FANUC 固定循环速查表:G73 / G81 / G82 / G83 / G84 / G85 / G86 / G87 / G88 × 地址字(X Y Z R Q P F K)× 相关参数(5121 / 5213 / 5200-5209)× 相关报警(045 / 073 / 074)
一张可直接引用的 FANUC 固定循环速查表:九个循环 × 地址字 × 参数 × 报警四向对照,每行带锚点。含九循环主表、X/Y/Z/R/Q/P/F/K 地址字全表、5121/5213/5200-5209 参数区段、045/073/074 ...
SINUMERIK 828D 固定循环参数速查:CYCLE81/82/83/84/840/85/86 中文参数说明 + FANUC G 循环迁移对照
828D 固定循环参数速查:PL/RP/SC/Z0/Z1/DT 与 G 代码 RTP/SDIS/DP/DPR 对照,CYCLE81/82/83/84/840/85/86 中文参数表与最小调用,CYCLE83 断屑(VARI=0)与排屑(VARI=1)、MPIT/PIT 攻丝二选...
海德汉 iTNC530 / TNC620 / TNC640 / TNC7 怎么区分与迁移?参数体系 MP→Cfg、循环兼容性与程序转换清单
iTNC 530 用 MP 机床参数、TNC 620/640/TNC7 用 Cfg 结构化配置,这是换机与升级的第一道分水岭。本文按海德汉官方资料给四代系统定位(控制环数、用途、界面)、程序与刀具表能否直接导入、循...
海德汉测头标定与在机测量参数:iTNC530 走 MP、TNC640/TNC7 走 Cfg,别改错地方
海德汉测头标定与在机测量参数完整指南:iTNC 530 与 TNC 640/620/TNC7 两代参数体系对照,3D 测头与触发式测头标定流程(CAL L / CAL R),标定值手动写回 TOOL.T 的官方条件(MP7411 / MP7260...
HEIDENHAIN TNC Fixed Cycle Parameter Reference: Cycle 200/203/230/251/252/4xx Q Parameters and FANUC G-Cycle Migration
HEIDENHAIN TNC fixed cycle Q-parameter reference: drilling 200-209, pocket milling 230/251/252, probing 4xx, tool measurement 48x with per-cycle Q meanings. Corrects the Q212/Q213 ...
Fanuc Tool Change Stuck: 4 Manual Fixes for a Jammed ATC Arm
Recovery actions for an already-jammed tool change, not a diagnostic procedure. Locate the jam among six possible points, then escalate by intervention depth: PMC force output (sta...
What Is a Fanuc PMC? Ladder Logic, Addresses and Scan Time
What is a PMC in Fanuc, and how does scan time decide ladder timing?
Mitsubishi M80/M70 Alarm Codes: Families, Detail Numbers and Reset
Mitsubishi M80/M70 alarms follow five families — M01, S, Y, Z, AL. The 4-digit detail number is the real fault ID: S01 0032 overcurrent needs a power cycle, S03 0050 overload clea...
Fanuc System Alarms 950, 971, 974: Meaning and Board-Level Diagnosis
Fanuc system alarms 900–976 in one table: 900 ROM PARITY, 910–919 memory parity, 920/921 axis cards, 926 FSSB, 930 CPU, 935 SRAM ECC, 950/951 PMC with the PCxxx detail code, 970...
FANUC Spindle Amplifier Alarm Codes 01-88 (SPM/PSM) and First Checks
Reading the two digits on the spindle amp LED? This full list maps FANUC SPM alarm codes 01–88 and A/b0/C0 letter codes to plain-English meaning, first action, and how to tell whe...






































