精彩推荐

数控机床电气调试必备软件全解析(2026版)-CNCShare | 数控电气技术中心
共享屋-CNCShare | 数控电气技术中心
数控机床电气工程师成长历程-CNCShare | 数控电气技术中心
共享屋积分与会员功能介绍-CNCShare | 数控电气技术中心
问题与反馈-CNCShare | 数控电气技术中心
最新发布第45页
Fanuc Backlash Compensation 1851: Measure, Convert to Detection Units, Write and Verify-CNCShare | 数控电气技术中心

Fanuc Backlash Compensation 1851: Measure, Convert to Detection Units, Write and Verify

The complete FANUC backlash compensation procedure: measure with a dial indicator at cutting feed and rapid, convert to detection units (0.020 mm becomes 20; lathe X axis times 2),...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
0636
FANUC LADDER III: Version Selection, Installation and Common Pitfalls-CNCShare | 数控电气技术中心

FANUC LADDER III: Version Selection, Installation and Common Pitfalls

A practical guide to FANUC LADDER III: which version matches which control, how to install it without the classic beginner failures, and how to get connected for online PMC monitor...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare21天前
01139
FANUC 参数怎么全部清零?RESET + DELETE 上电全清 + IPL 菜单逐项实操(顺带纠正一个流传很广的错误)-CNCShare | 数控电气技术中心

FANUC 参数怎么全部清零?RESET + DELETE 上电全清 + IPL 菜单逐项实操(顺带纠正一个流传很广的错误)

网上流传的「FANUC 恢复出厂设置」教程至少有一半是错的:0i-MD / 0i-MF 根本没有这个菜单项,真正的入口是断电后按住 RESET + DELETE 上电。本文区分四种「清」(RESET+DELETE / RESET / DELET...
三菱 M80 刀库乱刀怎么修:先分真假,再用 T 登录逐位修正-CNCShare | 数控电气技术中心

三菱 M80 刀库乱刀怎么修:先分真假,再用 T 登录逐位修正

三菱 M80 刀库乱刀的本质是系统记录的刀号与实际刀位对不上。不要照搬 M70 的 M77/M74/M79 维修代码,M80 的正确手段是 Setup 下的刀具登录逐位核对 + 主轴同步,再按信号/参数/机械三分法定位...
FANUC Matrix Keypad Panel Replacement: Remapping PMC Ladder Logic and Resolving R-Address Conflicts-CNCShare | 数控电气技术中心

FANUC Matrix Keypad Panel Replacement: Remapping PMC Ladder Logic and Resolving R-Address Conflicts

FANUC Matrix Keypad Panel Replacement: Remapping PMC Ladder Logic and Resolving R-Address Conflicts Field notes by 共享屋 (Gongxiangwu) — a real panel-swap job, compiled from wech...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare11天前
05513
FANUC 伺服报警三向对照总表:SV 号 / 放大器数码管码 / 诊断号怎么对-CNCShare | 数控电气技术中心

FANUC 伺服报警三向对照总表:SV 号 / 放大器数码管码 / 诊断号怎么对

同一次故障常同时看到 CNC 的 SV 报警号和放大器上的数码管码,但两者没有官方通用映射表。本页给出三套编码的关系、可核实的号段与码型、诊断号交叉列的正确用法和处理动作列。
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare5天前
04110
机床几何精度检测项 × 检具 × 判据 × 调整部位 对照框架:ISO 230-1 与 GB/T 17421.1 分册、五类几何误差族、判据来源纪律-CNCShare | 数控电气技术中心

机床几何精度检测项 × 检具 × 判据 × 调整部位 对照框架:ISO 230-1 与 GB/T 17421.1 分册、五类几何误差族、判据来源纪律

网上流传的「几何精度判据表」大多把标准号挂错、把某一台带 B 轴机型的七项当成通用清单、再给一组互相打架的允差数字。本页按 ISO 230-1 / GB/T 17421.1 重新搭框架,只给方法族与检索导航,...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
0618
数控电气调试软件与官方手册哪里下载?FANUC / 西门子 / 三菱 / 海德汉 官方入口与版本对应-CNCShare | 数控电气技术中心

数控电气调试软件与官方手册哪里下载?FANUC / 西门子 / 三菱 / 海德汉 官方入口与版本对应

只列厂商官方入口与可核实的文档编号:FANUC MyFANUC、西门子工业在线支持与 CNC4YOU、三菱 FA 下载中心、海德汉文档库与 TNCremo。按软件、用户手册、服务资料、机床厂资料分层,明确版本对应...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare前天
0469
Replacing a FANUC Servo Motor: Parameters 2020, 2022 and 2021, Re-measuring Inertia and Re-verifying Compensation-CNCShare | 数控电气技术中心

Replacing a FANUC Servo Motor: Parameters 2020, 2022 and 2021, Re-measuring Inertia and Re-verifying Compensation

FANUC servo motor replacement explained: amplifier swap versus motor swap, a correction to motor-side parameters (2021 inertia ratio, 2023 velocity pulses, 1825 position loop gain,...
cncshare的头像-CNCShare | 数控电气技术中心钻石会员cncshare昨天
0368