最新发布第19页
排序
SINUMERIK 828D 报警代码一览表（中文）— NC / PLC / SINAMICS F 代码三区对照与处理
SINUMERIK 828D 报警代码中文速查：NC / 轴 / 机床数据 / 700xxx / SINAMICS F 五段号段分区对照，含 2100 电池、2110 温度、2120 风扇、2130 口令、2140 维修开关等断电前必处理项，以及 F3000...
前天
What Is a PMC in Fanuc? Ladder Logic, Addresses and Scan Time
What is a PMC in Fanuc, and how does scan time decide ladder timing?
9天前
FANUC Servo Amplifier Replacement: Power-Off and Discharge, Teardown Order, Motor ID No.2020 Write-Back, Three Post-Swap Checks
A complete FANUC servo amplifier replacement procedure following official αi / βi parameter wording: the repair-or-replace decision, cutting main power (not the E-stop) and waiti...
7小时前
FANUC 0i-Mate / 0i-D Alarm Quick Reference: Same Number, Different Meaning + FSSB 5134-5198 and Serial Spindle 749/750
FANUC 0i / 0i-Mate alarm quick reference: on the old 0 series 950 is a +24V fuse while on 0i it is a PMC system alarm (24V moved to 960); FSSB 5134-5198 and serial spindle 749/750 ...
前天
FANUC 程序传不进机床？RS-232/CF卡/U盘/以太网/DNC 五种传输方式的参数、线序与故障对照
程序传不进 FANUC 机床，根因集中在四个点：线序没对、0020 通道没选对、通信格式两端不一致、媒体格式系统不认。本文按官方参数手册与连接手册口径，把 RS-232、存储卡、U 盘、以太网、DNC 五...
16小时前
Mitsubishi M80/M70 Servo Parameters: #2201-#2210 Full Table, #2233/#2238/#2246 Resonance Filters, #2235/#2237 Load Inertia Setup
Mitsubishi M80/M70 servo parameter reference: the complete #2201-#2210 block (PC1/PC2 gear ratio, PGN1 position loop, VGN1 speed loop), #2233/#2238/#2246 notch filter setup, #2235 ...
前天
FANUC 诊断画面速查：PMCDGN / STATUS / LAD / PARAM 四个画面分别查什么、怎么切
FANUC 诊断画面速查：PMCDGN / STATUS / LAD / PARAM 四个画面分别查什么、怎么切。SYSTEM → PMC 统一入口（0i-MD / 0i-MF / 30i 差异）、按按钮看 X 地址翻转的判定法、执行光标定位被 JMP/CJ...
7小时前
Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences
Tool measurement with a Heidenhain TT goes wrong for three recurring reasons: the cycle format does not match the control generation, the safety-zone parameter is looked for in the...
16小时前
SINUMERIK 840D PLC 用户报警详解：700000 段报警号 → DB2 位地址换算 + 自定义报警文本制作
840D PLC 用户报警 700000 段怎么查？本文给出 700xxyy → DB2.DBX 位地址换算公式（含 700806→244.6 算例）、用户区 0–9 地址速查表、UDT2/UDT1002 选型、FC10 的 ToUserIF 用法、ALARM_S/SQ...
21小时前
SINUMERIK 840D/828D UAFEHL Alarm: What It Means, Why the PLC Stops, and How to Localize It via DB2
UAFEHL is not a specific fault — it is the SINUMERIK flag for 'a user alarm triggered the PLC stop.' Six root-cause families, a 5-step localization procedure, SF/STOP/RUN LED mean...
3天前
扫一扫，添加我的微信
