最新发布第26页
排序
828D 设定数据 SD 和机床数据 MD 到底差在哪：号段规则、激活类型、访问等级与改错后的后果
828D 里 MD 与 SD 都存在 SRAM，但作用完全不同：MD 定义这台机器本身的物理与功能配置，改错会报警甚至撞机；SD 是操作员日常可调的运行参数，改动即时生效、风险低。本文给出官方功能手册的数...
19小时前
Setting Data (SD) vs Machine Data (MD) on SINUMERIK 828D: Number Ranges, Activation Types and Access Levels
On the 828D both MD and SD live in SRAM but do completely different jobs: MD defines what this machine physically is, and getting it wrong means alarms or even a crash; SD is the o...
19小时前
FANUC 换刀卡死怎么强制解开？机械手卡死 / 刀套不落位的四种手动恢复法（PMC 强制输出、电磁阀强给 24V、机械泄压、电机盘车）
换刀已经卡死时的救援动作，不是排查流程。先按六个断点分型定位，再按侵入深度从浅到深依次上手段：PMC 强制输出（普通 FORCE 需停 PMC，X/Y 自锁强制 OVERRIDE 不用停）→ 电磁阀脱离 PLC 直...
昨天
Fanuc Tool Change Stuck: Four Manual Recovery Methods for a Jammed ATC Arm (PMC Force Output, Direct 24V to the Solenoid, Pressure Relief, Motor Hand-Crank)
Recovery actions for an already-jammed tool change, not a diagnostic procedure. Locate the jam among six possible points, then escalate by intervention depth: PMC force output (sta...
昨天
FANUC 参数怎么全部清零？RESET + DELETE 上电全清 + IPL 菜单逐项实操（顺带纠正一个流传很广的错误）
网上流传的「FANUC 恢复出厂设置」教程至少有一半是错的：0i-MD / 0i-MF 根本没有这个菜单项，真正的入口是断电后按住 RESET + DELETE 上电。本文区分四种「清」（RESET+DELETE / RESET / DELET...
昨天
How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why “Restore Factory Settings” Does Not Exist)
A good half of the 'Fanuc restore factory settings' tutorials are wrong: there is no such menu on a 0i-MD / 0i-MF. The real entry is a hardware key combo - power down, hold RESET +...
昨天
FANUC PMC R9000 系列特殊继电器全表：系统保留地址含义 + 常 ON/OFF 与周期脉冲的实战用法
FANUC PMC 的 R9000 以上地址是系统保留区，只能读、不能写。本文讲清它为什么不能当普通继电器用，给出 R9091.0 常ON / R9091.1 常OFF / R9091.5·6 周期脉冲（±8ms 误差）/ R9000 运算结果位...
昨天
Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers
On a Fanuc PMC, addresses from R9000 upward are a system-reserved block you can read but must never write. This article explains why it is not a normal relay, gives a four-category...
昨天
FANUC 刀具寿命管理（TM）怎么开？8132#0 / 13203#7 / 6800 / 6813 参数 + G10 L3 编程 + F64.0 报警接线全流程
FANUC 刀具寿命管理（TM）把同型刀编成组、预设寿命、自动计数与换刀。本文按 0i-D/0i-F 核对 8132#0 开户、6813 最大组数、6800 组数×刀数、6800#2 次数/时间、13203#7 计数触发、6810 忽略号...
昨天
How to Set Up Fanuc Tool Life Management (TM): 8132#0 / 13203#7 / 6800 / 6813 Parameters + G10 L3 Programming + F64.0 Alarm Wiring
Fanuc Tool Life Management (TM) groups interchangeable tools, gives each group a life limit and counts down automatically. This guide covers enabling with 8132#0, max groups 6813 (...
昨天
扫一扫，添加我的微信
