最新发布第22页
排序
FANUC 宏程序（Macro B）教程：变量分区怎么选、G65/G66/G67 怎么用、嵌套上限与 PS 报警对照
FANUC 宏程序（Macro B）系统教程：变量三区怎么选（#1-#33 局部随调用清空、#100-#199 断电清零、#500-#999 保持型——工件计数与刀具寿命必须放 #500 段）、空值陷阱（没赋值的变量是 null 不...
15小时前
Fanuc Macro B Guide: Variable Partitions, G65/G66/G67 Calls, Nesting Limits and PS Alarm Codes
A complete Fanuc Custom Macro B guide: choosing the right variable partition (#1-#33 local variables cleared at return, #100-#199 common variables cleared at power off, #500-#999 r...
19小时前
SinuTrain for SINUMERIK Operate: Install, Program and Simulate on a PC
How to install and use SinuTrain for SINUMERIK Operate on a PC: what the Siemens simulation software does, which control generations it matches, the Windows 10/11 install steps, an...
14小时前
FANUC 诊断画面速查：PMCDGN / STATUS / LAD / PARAM 四个画面分别查什么、怎么切
FANUC 诊断画面速查：PMCDGN / STATUS / LAD / PARAM 四个画面分别查什么、怎么切。SYSTEM → PMC 统一入口（0i-MD / 0i-MF / 30i 差异）、按按钮看 X 地址翻转的判定法、执行光标定位被 JMP/CJ...
6小时前
FANUC 伺服放大器更换实操：断电放电 5 分钟、拆装顺序、电机 ID 与参数写回、换完必做的三项验证
FANUC 伺服放大器更换实操：从该不该换的决策、断电放电 5 分钟与验电挂牌、拆装顺序（先标记再拔线后拆螺丝）、电机 ID No.2020 与初始化位 No.2000#1 参数写回、FSSB 自动设定，到换完必做的...
14小时前
FANUC Servo Amplifier Replacement: Power-Off and Discharge, Teardown Order, Motor ID No.2020 Write-Back, Three Post-Swap Checks
A complete FANUC servo amplifier replacement procedure following official αi / βi parameter wording: the repair-or-replace decision, cutting main power (not the E-stop) and waiti...
6小时前
SINUMERIK 828D/840D 轮廓误差与跟随误差调参：25050 报警、Kv 因子、前馈、摩擦补偿与圆度测试（附参数速查表）
25050 轮廓监控报警怎么调？本文按西门子官方口径讲透 SINUMERIK 828D/840D 跟随误差与轮廓误差的调参顺序：三个监控报警的阶段区别、Kv 因子 MD32200 与跟随误差的定量关系、前馈 MD32620 系列...
17小时前
SINUMERIK 828D/840D Following Error and Contour Error Tuning: 25050 Alarms, Kv Factor, Feedforward and the Circularity Test
What to do when 25050 contour monitoring alarms? Following official Siemens wording, this article covers the tuning order for following error and contour error on SINUMERIK 828D/84...
16小时前
FANUC 程序传不进机床？RS-232/CF卡/U盘/以太网/DNC 五种传输方式的参数、线序与故障对照
程序传不进 FANUC 机床，根因集中在四个点：线序没对、0020 通道没选对、通信格式两端不一致、媒体格式系统不认。本文按官方参数手册与连接手册口径，把 RS-232、存储卡、U 盘、以太网、DNC 五...
16小时前
FANUC Program Transfer: RS-232, Memory Card, USB, Ethernet and DNC — Pinout, Parameters and Troubleshooting
Transferring a program into a FANUC control fails for four recurring reasons: wrong cable pinout, wrong 0020 I/O channel, mismatched serial frame settings, or a media format the co...
6小时前
扫一扫，添加我的微信
