最新发布第21页
排序
技术人员做公众号能赚钱吗？2个实测有效的变现方法
专为技术人员打造的公众号变现指南。详解2026年公众号流量主、广告接单、知识付费三大变现方式，结合电气/数控领域实测案例，附运营技巧与收益数据。零粉丝也能起步。
9天前
Fanuc Backlash Compensation 1851: Measure, Convert to Detection Units, Write and Verify
The complete FANUC backlash compensation procedure: measure with a dial indicator at cutting feed and rapid, convert to detection units (0.020 mm becomes 20; lathe X axis times 2),...
昨天
三菱 M80 数控系统常见报警处理：ALM401 / S01 / Z70 / AL 驱动码完整对照
三菱 M80 报警两层结构：NC 屏报警与 MDS 驱动器 7 段 AL 码的对应关系，EMG 急停用 R69 定位（Bit4 EXIN / Bit6 PLC / BitE SPIN / BitF SRV），S01/S02/S03 的复位类别与详细编号，Z70/Z71/Z7...
前天
SinuTrain for SINUMERIK Operate: Install, Program and Simulate on a PC
How to install and use SinuTrain for SINUMERIK Operate on a PC: what the Siemens simulation software does, which control generations it matches, the Windows 10/11 install steps, an...
14小时前
FANUC 螺距误差补偿 3620–3624 全流程：激光干涉仪测量 → 补偿点编号计算 → 参数填写 → 精度验证
FANUC 螺距误差补偿 3620-3624 全流程：跨代参数对照表（0M 0712-0715/1000-1128 ↔ i 系列 3620-3624 ↔ 16i/18i 双向 3605#0/3626/3627）、激光干涉仪测量与单向定位逼近、补偿点编号计算（负...
昨天
FANUC SERVO GUIDE: Waveform Analysis, Vibration Suppression and Rigid Tapping
A field guide to FANUC SERVO GUIDE: what it does, which controls it supports, how to install and connect over Ethernet, and the four workflows that solve most servo problems.
14小时前
FANUC LADDER III: Compile, Decompile and Program Protection Explained
Why FANUC LADDER III needs compile and decompile: compile to download or monitor online, decompile to edit or analyze an uploaded program. Plus how ladder program password protecti...
4天前
“FANUC Data Backup and Recovery: ALL I/O Full Backup vs BOOT SRAM Backup — 3 Methods Compared + Restore Steps”
'FANUC data backup explained: when to use ALL I/O one-click full backup (0i-F / 0i-F Plus), BOOT SRAM backup (system won't boot), or itemized backup. Covers parameters 0020 / 0313#...
昨天
SINUMERIK 828D 报警代码一览表（中文）— NC / PLC / SINAMICS F 代码三区对照与处理
SINUMERIK 828D 报警代码中文速查：NC / 轴 / 机床数据 / 700xxx / SINAMICS F 五段号段分区对照，含 2100 电池、2110 温度、2120 风扇、2130 口令、2140 维修开关等断电前必处理项，以及 F3000...
前天
FANUC Servo Amplifier Replacement: Power-Off and Discharge, Teardown Order, Motor ID No.2020 Write-Back, Three Post-Swap Checks
A complete FANUC servo amplifier replacement procedure following official αi / βi parameter wording: the repair-or-replace decision, cutting main power (not the E-stop) and waiti...
6小时前
扫一扫，添加我的微信
