最新发布第21页
排序
Heidenhain TNC Error Code List: How to Read 6-Digit Codes + High-Frequency Faults by Family
The Heidenhain TNC error code reference: how to read the six-digit format (three-digit family + four hexadecimal digits), the full family map from 120 to 330 with the NC versus mac...
15小时前
海德汉测头标定与在机测量参数：iTNC530 走 MP、TNC640/TNC7 走 Cfg，别改错地方
海德汉测头标定与在机测量参数完整指南：iTNC 530 与 TNC 640/620/TNC7 两代参数体系对照，3D 测头与触发式测头标定流程（CAL L / CAL R），标定值手动写回 TOOL.T 的官方条件（MP7411 / MP7260...
15小时前
Heidenhain Touch Probe Calibration: iTNC 530 Uses MP, TNC 640/TNC7 Uses Cfg — Calibrate in the Right Place
The complete Heidenhain touch probe calibration and in-machine measurement reference: the iTNC 530 versus TNC 640/620/TNC7 parameter generations, 3-D and touch-trigger probe calibr...
15小时前
“FANUC Data Backup and Recovery: ALL I/O Full Backup vs BOOT SRAM Backup — 3 Methods Compared + Restore Steps”
'FANUC data backup explained: when to use ALL I/O one-click full backup (0i-F / 0i-F Plus), BOOT SRAM backup (system won't boot), or itemized backup. Covers parameters 0020 / 0313#...
昨天
828D 用户报警位地址速查：DB1600 顺序算法（700000–700247 / 701000–701999 扩展）
SINUMERIK 828D 用户报警位地址速查：DB1600 顺序算法与 840D DB2 分组算法的逐项对照（700247 在 828D 是 DB1600.DBX30.7，在 840D 是 DB2.DBX201.7），248 条标准报警全表推算法，701000–701...
20小时前
SINUMERIK 828D User Alarm Bits: DB1600 Sequential Mapping and Extended 701000-701999
The SINUMERIK 828D user alarm bit address reference: the DB1600 sequential mapping contrasted item by item with the 840D DB2 grouped algorithm (700247 is DB1600.DBX30.7 on the 828D...
20小时前
828D 扩展用户报警 701000–701999 怎么加？DB9913 配置数据 + DB1600 高位段实操
SINUMERIK 828D 扩展用户报警完整配置教程：248 条用完后如何启用 701000–701999 这 1000 条扩展报警（总容量 248+1000=1248），PPU24x.3/PPU27x.4 以上硬件、V4.7.4 以上软件、PLC Programmin...
20小时前
SINUMERIK 828D Extended User Alarms 701000-701999: DB9913 Configuration and High DB1600 Bits
A complete configuration tutorial for SINUMERIK 828D extended user alarms: how to enable the 701000-701999 range (1000 extra alarms on top of the standard 248, for a documented tot...
20小时前
828D 全闭环改半闭环怎么改？屏蔽光栅尺的 MD 参数 + PLC 位 + 间隙补偿三件套
SINUMERIK 828D 全闭环改半闭环完整教程：光栅尺故障应急屏蔽与永久改半闭环的三层改法——NC 机床数据（MD30200 测量系统数量、MD30230 输入分配把电机编码器排到第一路、MD31000/31010/31020/...
20小时前
SINUMERIK 828D Semi-Closed Loop Conversion: MD Parameters, PLC Bits and Gap Compensation
A complete SINUMERIK 828D semi-closed loop conversion guide for masking a faulty linear scale: the three layers that must move together — NC machine data (MD30200 number of measur...
20小时前
扫一扫，添加我的微信
