cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
加工尺寸忽大忽小怎么查?四条线分离法:机械线 / 检测反馈线 / 工艺刀具线 / 数据基准线,一次把波动源分开-CNCShare | 数控电气技术中心

加工尺寸忽大忽小怎么查?四条线分离法:机械线 / 检测反馈线 / 工艺刀具线 / 数据基准线,一次把波动源分开

尺寸忽大忽小别再靠反复调刀补硬压 —— 刀补只修稳定的系统偏差,修不了随机漂移。用四条线分离法先判断「变化跟着什么走」:随件数走是刀具磨损,随时间走是热变形,随位置走是丝杠/螺距,随...
SINUMERIK 828D G290 G291 怎么切?DIN 写法与 ISO 写法逐行对照-CNCShare | 数控电气技术中心

SINUMERIK 828D G290 G291 怎么切?DIN 写法与 ISO 写法逐行对照

G290 激活西门子 NC 编程语言,G291 激活 ISO 方言;两者必须单独成段,同段禁止混写。本页给出程序头、换刀、主轴、轮廓、循环的逐行对照,并用西门子官方手册纠正“模式可互相识别”的真正含...
FANUC Matrix Keypad Panel Replacement: Remapping PMC Ladder Logic and Resolving R-Address Conflicts-CNCShare | 数控电气技术中心

FANUC Matrix Keypad Panel Replacement: Remapping PMC Ladder Logic and Resolving R-Address Conflicts

FANUC Matrix Keypad Panel Replacement: Remapping PMC Ladder Logic and Resolving R-Address Conflicts Field notes by 共享屋 (Gongxiangwu) — a real panel-swap job, compiled from wech...
海德汉 TNC「防护门未关 / 门未关」报警怎么查:安全链四层定位 + 门开关门锁排查 + 改动后四项验证-CNCShare | 数控电气技术中心

海德汉 TNC「防护门未关 / 门未关」报警怎么查:安全链四层定位 + 门开关门锁排查 + 改动后四项验证

海德汉 TNC 报「防护门未关 / DOOR OPEN / GUARD NOT CLOSED」,本质不是 NC 软件故障,而是 PLC 把「门关闭条件」判成 false。本文按安全链四层(门开关机械 → 安全继电器 → PLC 数字量输入 ...
Fanuc Servo Load Meter Explained: Bands, 3111 Switches and Diagnostics 200-204 / 300-CNCShare | 数控电气技术中心

Fanuc Servo Load Meter Explained: Bands, 3111 Switches and Diagnostics 200-204 / 300

POS monitor for patrol, SV monitor for decisions, diagnostics for causes. Covers what 'actual current (%)' really means, peaks versus sustained load, and two common parameter-bit m...
7天前
0568
海德汉 TCH PROBE 31/481 测刀循环参数对照:iTNC530 走 MP、TNC640 走 Cfg,逐齿上限 99 与 20 的分界-CNCShare | 数控电气技术中心

海德汉 TCH PROBE 31/481 测刀循环参数对照:iTNC530 走 MP、TNC640 走 Cfg,逐齿上限 99 与 20 的分界

对刀仪测刀测不准,根子多在循环格式选错代、安全区参数找错地方、TOOL.T 该预填的字段空着。本文按官方手册口径讲透 TCH PROBE 31 与 481 的两代格式差异、Q340 覆写/比较/只读三模式、Q260 安...
FANUC PMC Functional Instruction (SUB) Quick Reference: Numbers, Families and Model Availability-CNCShare | 数控电气技术中心

FANUC PMC Functional Instruction (SUB) Quick Reference: Numbers, Families and Model Availability

PMC functional instructions are called by SUB number, but the same SUB number is not available on every PMC model. Verifiable SUB numbers and families from official Table 5(a), rea...
3天前
05614
Spindle Runout: Four-Layer Diagnosis, the Two-Point Test Arbor Split and Taper Contact Pattern Checking-CNCShare | 数控电气技术中心

Spindle Runout: Four-Layer Diagnosis, the Two-Point Test Arbor Split and Taper Contact Pattern Checking

Runout guides publish a single universal tolerance and diagnose every far-point reading as a bearing preload problem. The two-point reading only gives a direction, and published so...
7天前
05613
HEIDENHAIN TNC Conversational Programming for Beginners: One Minimal Program-CNCShare | 数控电气技术中心

HEIDENHAIN TNC Conversational Programming for Beginners: One Minimal Program

HEIDENHAIN Klartext is conversational programming - the screen asks, you answer, no G-code memorising. Using a 13-line minimal program, this explains BEGIN PGM, BLK FORM blank, TOO...
3天前
0566
Fanuc Tool Setter / Probe Calibration: Parameters 5015-5018, G31 / G36 / G37 and the O9000 Macro Chain-CNCShare | 数控电气技术中心

Fanuc Tool Setter / Probe Calibration: Parameters 5015-5018, G31 / G36 / G37 and the O9000 Macro Chain

Parameters 5015 and 5016 are not ID and OD tools. The official Fanuc additional manual defines four contact surfaces. Four reference distances, a six-step field calibration, skip v...
7天前
0565
广告合作 / 商务合作