cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
海德汉 TNC 对话式编程入门:一个最小程序看懂 BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/循环-CNCShare | 数控电气技术中心

海德汉 TNC 对话式编程入门:一个最小程序看懂 BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/循环

海德汉 Klartext 对话式编程,屏幕问一句你答一句,不用背 G 代码。本文用一个 13 行能跑的最小程序,逐行讲清 BEGIN PGM、BLK FORM 毛坯、TOOL CALL 刀具、L 直线、C/CR 圆弧、R0/RL/RR 补偿、...
FANUC I/O Link Address Assignment: Group.Base.Slot, OC01I / OC02I and the 16-Byte Handwheel Rule-CNCShare | 数控电气技术中心

FANUC I/O Link Address Assignment: Group.Base.Slot, OC01I / OC02I and the 16-Byte Handwheel Rule

I/O Link address assignment is a four-part expression of group, base, slot and module byte count. Module byte counts, why a handwheel needs 16 bytes, I/O Link vs I/O Link i, and a ...
7天前
05812
FANUC 16i / 18i / 21i / 30i / 31i Identification: Model Reading, Axis Counts and Spare-Part Selection-CNCShare | 数控电气技术中心

FANUC 16i / 18i / 21i / 30i / 31i Identification: Model Reading, Axis Counts and Spare-Part Selection

A control in the shop says only '18i' on the panel - which generation, how many axes, and can spares be swapped? Official B-63002EN / B-63522EN axis totals include loader axes and ...
5天前
05813
FANUC Servo Amplifier Replacement: Power-Off and Discharge, Teardown Order, Motor ID No.2020 Write-Back, Three Post-Swap Checks-CNCShare | 数控电气技术中心

FANUC Servo Amplifier Replacement: Power-Off and Discharge, Teardown Order, Motor ID No.2020 Write-Back, Three Post-Swap Checks

A complete FANUC servo amplifier replacement procedure following official αi / βi parameter wording: the repair-or-replace decision, cutting main power (not the E-stop) and waiti...
前天
0576
FANUC 高速高精度 / 平滑控制跨机型对照表:AICC、纳米平滑、G05.1 Q1 与官方手册可核实的参数-CNCShare | 数控电气技术中心

FANUC 高速高精度 / 平滑控制跨机型对照表:AICC、纳米平滑、G05.1 Q1 与官方手册可核实的参数

一页查清 AICC / AI 纳米轮廓控制的叫法、G05.1 Q1/Q0 指令格式、官方手册可核实的参数(7066、19520、1620/1622 等)与跨机型确认方法。网传的「AICC 参数号全表」来源互相矛盾,本表逐条标明...
FANUC AICC / Nano Smoothing Setup: G05.1 Q1, Parameter-Side Enable, and Six Reasons It Does Nothing-CNCShare | 数控电气技术中心

FANUC AICC / Nano Smoothing Setup: G05.1 Q1, Parameter-Side Enable, and Six Reasons It Does Nothing

G05.1 Q1 turns on high-speed high-precision contour control and Q0 cancels it, but the G-code alone is not enough. This guide covers the PRMTUN high-precision setup path, checking ...
14天前
0576
FANUC 仿真软件怎么选?官方 CNC Guide 四件套、授权方式与「免费版」的合规边界-CNCShare | 数控电气技术中心

FANUC 仿真软件怎么选?官方 CNC Guide 四件套、授权方式与「免费版」的合规边界

搜「FANUC 仿真软件下载」的人大多冲着「免费版」去,但 FANUC 官方仿真(CNC Guide)是带硬件密钥的授权产品;网传「官方仿真仅美洲提供」也是错的。本页把官方四件套的规格、两种硬件密钥、第...
SINUMERIK 828D/802D 数据丢了还能救吗?程序/参数/PLC 三层恢复顺序与缺省模式启动操作详解-CNCShare | 数控电气技术中心

SINUMERIK 828D/802D 数据丢了还能救吗?程序/参数/PLC 三层恢复顺序与缺省模式启动操作详解

828D/802D 数据丢了怎么救:先判断丢的是 NC/PLC/驱动/HMI 哪一层,读懂 4062 与 4060 相反的含义,再按内部备份、.ard 存档、缺省模式启动三条路径恢复。含 SUNRISE 口令与轴名错位提醒。
How to Classify and Troubleshoot CNC Homing Failures: Reference Not Found vs Wrong Reference Position + Decel Dog / One-Turn Signal + Grid Shift 1850 / Reference Counter 1821 + Absolute Encoder Battery-CNCShare | 数控电气技术中心

How to Classify and Troubleshoot CNC Homing Failures: Reference Not Found vs Wrong Reference Position + Decel Dog / One-Turn Signal + Grid Shift 1850 / Reference Counter 1821 + Absolute Encoder Battery

Stop swapping parts to see what sticks. Split homing failures into two classes: reference not found, and reference position wrong. In the first class, watch whether the axis decele...
前天
0578
加工尺寸忽大忽小怎么查?四条线分离法:机械线 / 检测反馈线 / 工艺刀具线 / 数据基准线,一次把波动源分开-CNCShare | 数控电气技术中心

加工尺寸忽大忽小怎么查?四条线分离法:机械线 / 检测反馈线 / 工艺刀具线 / 数据基准线,一次把波动源分开

尺寸忽大忽小别再靠反复调刀补硬压 —— 刀补只修稳定的系统偏差,修不了随机漂移。用四条线分离法先判断「变化跟着什么走」:随件数走是刀具磨损,随时间走是热变形,随位置走是丝杠/螺距,随...
广告合作 / 商务合作