cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
SINUMERIK 828D / 840D sl Shortcut Keys Verified Against the Official Manuals: Six Operating Areas, Ctrl / Alt Keys and the ARC / ARD Split-CNCShare | 数控电气技术中心

SINUMERIK 828D / 840D sl Shortcut Keys Verified Against the Official Manuals: Six Operating Areas, Ctrl / Alt Keys and the ARC / ARD Split

Circulating 'complete Sinumerik shortcut lists' are same-source reprints that get 840D sl Ctrl+Alt+S wrong, rename the sixth operating area and drop two official notes. Every key c...
7天前
03712
Replacing a FANUC Servo Motor: Parameters 2020, 2022 and 2021, Re-measuring Inertia and Re-verifying Compensation-CNCShare | 数控电气技术中心

Replacing a FANUC Servo Motor: Parameters 2020, 2022 and 2021, Re-measuring Inertia and Re-verifying Compensation

FANUC servo motor replacement explained: amplifier swap versus motor swap, a correction to motor-side parameters (2021 inertia ratio, 2023 velocity pulses, 1825 position loop gain,...
前天
0368
Used CNC Machine Electrical Inspection Checklist — 30 Checks Before You Pay the Balance-CNCShare | 数控电气技术中心

Used CNC Machine Electrical Inspection Checklist — 30 Checks Before You Pay the Balance

The most expensive mistake in a used CNC purchase is in the electrical cabinet. This 30-point field checklist covers history verification, power-off checks, live testing, and how t...
7天前
0369
CNC 24 V / 5 V Control Power Faults: SV0434 and 230041 Official Definitions, the PS0003 Number Conflict, and No-Load / Load Separation-CNCShare | 数控电气技术中心

CNC 24 V / 5 V Control Power Faults: SV0434 and 230041 Official Definitions, the PS0003 Number Conflict, and No-Load / Load Separation

A widely copied checklist presents PS0003, SV0434 and 230041 as one fault with three brand codes and publishes a voltage table as if it were official. PS0003 has two conflicting pu...
7天前
0356
SINUMERIK 828D Third Handwheel and Mini HHU: MD11350, FB1 and DB11/DB21/DB31-CNCShare | 数控电气技术中心

SINUMERIK 828D Third Handwheel and Mini HHU: MD11350, FB1 and DB11/DB21/DB31

The third handwheel goes to MCP X60. MD11350=5 (828D) and =7 (840D sl PN MCP) differ; FB1 and three PLC signal areas decide if the axis moves.
11天前
0357
接近开关 NPN / PNP / NAMUR 到底怎么选怎么接?机床三大角色(硬限位 / 原点 / 刀位检测)的不同选法 + 常闭优先的失效安全 + 误动作四查-CNCShare | 数控电气技术中心

接近开关 NPN / PNP / NAMUR 到底怎么选怎么接?机床三大角色(硬限位 / 原点 / 刀位检测)的不同选法 + 常闭优先的失效安全 + 误动作四查

接近开关在机床上有三大角色:硬限位、原点、刀位/工件检测,选法各不相同。本篇聚焦机床场景讲清 NPN/PNP 取决于 PLC 输入公共端、NAMUR 两线本安回路、硬限位为何必须常闭失效安全、原点开关...
FANUC Alarm History and Operation History: Using 3106#4 OPH to Trace Intermittent Faults-CNCShare | 数控电气技术中心

FANUC Alarm History and Operation History: Using 3106#4 OPH to Trace Intermittent Faults

Intermittent faults cannot be reproduced on demand, so the only evidence is the timeline. Based on the official FANUC maintenance manual, this guide covers 3106#4 OPH, 3106#7 OHS, ...
2天前
03512
FANUC High-Speed / Smoothing Parameter Cross-Reference by Control Generation: AICC, AI Nano CC and G05.1 Q1-CNCShare | 数控电气技术中心

FANUC High-Speed / Smoothing Parameter Cross-Reference by Control Generation: AICC, AI Nano CC and G05.1 Q1

One-page cross-reference for FANUC high-speed and smoothing functions: names, G05.1 Q1/Q0 command format, parameters verifiable in official manuals (7066, 19520, 1620/1622), and ho...
7天前
03413
FANUC 换伺服电机后参数怎么回写?2020 / 2022 / 2021 + 惯量比重测 + 编码器方向与对位 + 三步验收-CNCShare | 数控电气技术中心

FANUC 换伺服电机后参数怎么回写?2020 / 2022 / 2021 + 惯量比重测 + 编码器方向与对位 + 三步验收

FANUC 换伺服电机全解:先分清换放大器与换电机,给出电机侧参数纠错(2021 惯量比、2023 速度脉冲数、1825 位置环增益,非网传的 2023/2083),惯量比重测三法、编码器对位、机械电气侧检查、...
Fanuc Rigid Tapping Parameters Explained: M29/G84 Sync, the 5200–5294 Chain and SP0741 Alarm Troubleshooting (with DGN 452/453)-CNCShare | 数控电气技术中心

Fanuc Rigid Tapping Parameters Explained: M29/G84 Sync, the 5200–5294 Chain and SP0741 Alarm Troubleshooting (with DGN 452/453)

Bad rigid tapping is usually not the program - it is the parameters nobody explained. This guide splits the 5200-5294 group into five blocks: enable bits that decide whether you ta...
3天前
03414
广告合作 / 商务合作