cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
840D sl 安全集成报警 27097/27801/27810/27350 怎么查:SPL 启动、安全模式、F_DP 通信与对应机床数据-CNCShare | 数控电气技术中心

840D sl 安全集成报警 27097/27801/27810/27350 怎么查:SPL 启动、安全模式、F_DP 通信与对应机床数据

840D sl 的 SINUMERIK Safety Integrated 报警 27097(SPL 启动未执行)、27801/27810(安全模式与 PLC 配置不一致)、27350/27351(F_DP 通信错误)怎么查。逐一对应机床数据 MD28082/28083/11...
FANUC 伺服报警三向对照总表:SV 号 / 放大器数码管码 / 诊断号怎么对-CNCShare | 数控电气技术中心

FANUC 伺服报警三向对照总表:SV 号 / 放大器数码管码 / 诊断号怎么对

同一次故障常同时看到 CNC 的 SV 报警号和放大器上的数码管码,但两者没有官方通用映射表。本页给出三套编码的关系、可核实的号段与码型、诊断号交叉列的正确用法和处理动作列。
Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers-CNCShare | 数控电气技术中心

Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers

The manual calls it F30020, a 828D screen shows 230020 - one fault, two numbering systems. This table maps SINAMICS F codes to 828D/840D sl display numbers, fault meanings and firs...
2天前
04110
数控 24V / 5V 控制电源故障怎么查?SV0434 与 230041 官方口径 + PS0003 编号冲突 + 空载负载分离法-CNCShare | 数控电气技术中心

数控 24V / 5V 控制电源故障怎么查?SV0434 与 230041 官方口径 + PS0003 编号冲突 + 空载负载分离法

简报把 PS0003 / SV0434 / 230041 写成三品牌同源现象,又把经验电压表当成官方判据。核实后:PS0003 存在两套互相冲突的解释,SV0434 与 230041 的检测位置和阈值完全不同。本页把官方口径与经...
SINUMERIK 840D sl to S7-1500: NCVAR Selector, PROFINET Names and Alarm 150202-CNCShare | 数控电气技术中心

SINUMERIK 840D sl to S7-1500: NCVAR Selector, PROFINET Names and Alarm 150202

A healthy PROFINET link does not give the PLC direct access to SINUMERIK machine data. This guide separates Siemens-confirmed facts from the version-dependent field workflow: Selec...
5天前
0418
Fanuc 0i-B / 0i-C Legacy Alarms: Same Number, Different Board - 920 / 930 / 950 / 974 / 975 Decoded-CNCShare | 数控电气技术中心

Fanuc 0i-B / 0i-C Legacy Alarms: Same Number, Different Board – 920 / 930 / 950 / 974 / 975 Decoded

On a 0i-B or 0i-C the alarms are plain numbers with no SV/PS prefix, and a 920 does not point to the same hardware as on a 0i-D/0i-F. The 900 range verified against manual B-64115E...
5天前
04014
FANUC 固定循环速查表:G73 / G81 / G82 / G83 / G84 / G85 / G86 / G87 / G88 × 地址字(X Y Z R Q P F K)× 相关参数(5121 / 5213 / 5200-5209)× 相关报警(045 / 073 / 074)-CNCShare | 数控电气技术中心

FANUC 固定循环速查表:G73 / G81 / G82 / G83 / G84 / G85 / G86 / G87 / G88 × 地址字(X Y Z R Q P F K)× 相关参数(5121 / 5213 / 5200-5209)× 相关报警(045 / 073 / 074)

一张可直接引用的 FANUC 固定循环速查表:九个循环 × 地址字 × 参数 × 报警四向对照,每行带锚点。含九循环主表、X/Y/Z/R/Q/P/F/K 地址字全表、5121/5213/5200-5209 参数区段、045/073/074 ...
HEIDENHAIN iTNC 530 vs TNC 620 / 640 / TNC7: Differences, MP vs Cfg, and Program Migration-CNCShare | 数控电气技术中心

HEIDENHAIN iTNC 530 vs TNC 620 / 640 / TNC7: Differences, MP vs Cfg, and Program Migration

iTNC 530 uses MP machine parameters while TNC 620/640/TNC7 use structured Cfg objects — the first divide in any retrofit or upgrade. This guide uses official HEIDENHAIN data for g...
前天
0407
FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查-CNCShare | 数控电气技术中心

FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查

间歇故障复现不了,只能靠「什么时候报的」串证据。本文按 FANUC 官方维修手册给出 3106#4 OPH、3106#7 OHS、3122 时标间隔与外部操作消息历史的位定义、操作履历画面调出路径,纠正网上把 #4/#...
SINUMERIK 828D NCK Battery Alarm 2100/2101/2102: Replace Live or Power Down?-CNCShare | 数控电气技术中心

SINUMERIK 828D NCK Battery Alarm 2100/2101/2102: Replace Live or Power Down?

The complete guide to SINUMERIK 828D NCK battery alarms 2100/2101/2102: the three voltage thresholds and their remedy windows, replacing live with the 30-minute buffer capacitor (n...
10天前
04013
广告合作 / 商务合作