cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
SINUMERIK 802D sl 报警速查:NCK / PROFIBUS / PLC / 用户报警号段与官方检索路径-CNCShare | 数控电气技术中心

SINUMERIK 802D sl 报警速查:NCK / PROFIBUS / PLC / 用户报警号段与官方检索路径

802D sl 报警不能按「五位 NC、六位 PLC」分。本页按官方诊断手册给出三条号段线、700000 用户报警接口、25050 完整条目、系统反应与按号全文检索的手册导航。
Fanuc Override Setup: Parameters 1420-1425, G12 / G14 Signals and Four Failure Checks-CNCShare | 数控电气技术中心

Fanuc Override Setup: Parameters 1420-1425, G12 / G14 Signals and Four Failure Checks

The fourth rapid-override step is F0, not 10%. G12 is 8-bit negative logic covering 0-254%. G6.4 clamps cutting feed only. The official start-up manual split of 1420-1425, the sign...
7天前
0439
840D sl Safety Integrated Alarms 27097 / 27801 / 27810 / 27350 — SPL Start, Safe Mode Mismatch, F_DP Communication (with Machine Data)-CNCShare | 数控电气技术中心

840D sl Safety Integrated Alarms 27097 / 27801 / 27810 / 27350 — SPL Start, Safe Mode Mismatch, F_DP Communication (with Machine Data)

How to diagnose SINUMERIK 840D sl Safety Integrated alarms 27097 (SPL not started), 27801/27810 (safe operating mode vs PLC config mismatch), and 27350/27351 (F_DP communication er...
7天前
04315
FANUC 0i-F / 0i-F Plus 功能选项对照与「我这台机器到底装了什么」怎么查:规格表图例、选件族与代号纠错-CNCShare | 数控电气技术中心

FANUC 0i-F / 0i-F Plus 功能选项对照与「我这台机器到底装了什么」怎么查:规格表图例、选件族与代号纠错

手册里有 AI 轮廓控制,为什么机床上用不了?操作手册描述的是全部可选功能。本页按官方 0i-F Plus 规格表讲清「书里有不等于机器上有」、符号图例、三种查证路径,并纠正几处选件代号误传。
Fanuc Parameter Number Map by Range: Which Block Controls What-CNCShare | 数控电气技术中心

Fanuc Parameter Number Map by Range: Which Block Controls What

No universal 0000-9999 Fanuc parameter table exists. Chapter 4 functional block framework, verifiable landmark parameters, a change-risk grading, number-based manual lookup keys an...
前天
0427
CNC Servo Vibration, Overshoot and Noise: A Phenomenon-Based Troubleshooting Table-CNCShare | 数控电气技术中心

CNC Servo Vibration, Overshoot and Noise: A Phenomenon-Based Troubleshooting Table

Classify servo vibration into 4 types (high-frequency squeal, low-frequency flutter, start/stop overshoot, machining ripple) and follow the right branch. Covers HRV filters, inerti...
14天前
0427
Refurbished vs New FANUC Servo Amplifier: Cost Comparison and Repair-or-Replace Decision Table-CNCShare | 数控电气技术中心

Refurbished vs New FANUC Servo Amplifier: Cost Comparison and Repair-or-Replace Decision Table

Comparing repair cost against new-part cost is the wrong way to decide. This guide covers repairability assessment, three tiers of repair, three replacement options, and a four-fac...
5天前
0425
Mitsubishi MT Works2 / MR Configurator2: Official Download Path, Modules and Servo Parameters-CNCShare | 数控电气技术中心

Mitsubishi MT Works2 / MR Configurator2: Official Download Path, Modules and Servo Parameters

Mitsubishi servo tuning software explained: MT Works2 suite versus MR Configurator2, the official download path (no cloud drive), connecting MR-J4/J5, PA01/PA05/PA06 parameter exam...
3天前
0425
Bypassing a FANUC Linear Scale: Full to Semi Closed-Loop Conversion with 1815#1, 2024, 2084/2085 and 2185-CNCShare | 数控电气技术中心

Bypassing a FANUC Linear Scale: Full to Semi Closed-Loop Conversion with 1815#1, 2024, 2084/2085 and 2185

How to temporarily bypass a FANUC linear scale and switch from full to semi closed-loop: 1815#1/#5, 2024, 2084/2085, 2185, 1821, 1850, 1851/1852, 2003#5 and 2019#7. Marks the dispu...
3天前
04215
Mitsubishi M80 Z60 / Z67 / Z68 / Z14: Fieldbus, CC-Link and CC-Link IE Field-CNCShare | 数控电气技术中心

Mitsubishi M80 Z60 / Z67 / Z68 / Z14: Fieldbus, CC-Link and CC-Link IE Field

Z60 belongs to the FCU8-WN563 fieldbus, Z67/Z68 to CC-Link, and Z14 to the CC-Link IE Field hardware test. Read n1-n4, SW0080-0083 and the official terminating resistor values befo...
11天前
04212
广告合作 / 商务合作