海德汉 TNC 型号 × 参数体系 × 循环兼容性对照表:iTNC530 / TNC620 / TNC640 / TNC7 一次查全
一页查全四代海德汉系统的定位、控制环数、NC 软件号、参数体系(MP vs Cfg)与入口,以及官方标注过的 MP↔Cfg 逐项映射。没有可靠来源的行明确留白并给出查法,不编 MP 号对照表。
SINUMERIK 828D 参数与程序备份恢复完整教程(Archiving + USB + Archive 格式实操)
828D 备份恢复完整教程:备份前 3 件事(电池 / U 盘必须 FAT32 / 记录版本)、调试存档 ard 的创建与读入逐步流程、菜单各选项含义、自动数据备份 asd 配置、恢复后必查 3 项、跨机跨版本导入...
SINUMERIK 828D Extended User Alarms 701000-701999: DB9913 Configuration and High DB1600 Bits
A complete configuration tutorial for SINUMERIK 828D extended user alarms: how to enable the 701000-701999 range (1000 extra alarms on top of the standard 248, for a documented tot...
SINUMERIK Drive Faults Explained: F30020, F30021, F30011, F07011 and A30010 — the 230xxx Mapping, r0949 Fault Values and First Checks
The 828D shows 230020 but the manual says F30020 - one fault, two numbering systems. This guide explains how to translate display numbers back to the manual, locate the alarm famil...
GSK CNC Alarm Code Reference: 980T / 980TD / 988T / 988TA Number Ranges and PLC Alarms 1000-1037 with A-Addresses
Search results for GSK alarm codes are dominated by English sites. This page verifies the framework against the GSK988T User Manual Appendix A.8 and the 980TDb standard ladder: 980...
How to Write Mitsubishi M80 Ladder Logic into the CNC — RAM Write, ROM Copy and Checksum ERROR
How to write the Mitsubishi M80 / M800 ladder logic (the embedded PLC sequence program) into the CNC — the GX Developer / GX Works2·3 RAM write flow, why you must 'copy to ROM', ...
数控机床电气原理图怎么看?符号/线号/主回路/控制回路/PMC 地址反查一图读懂
从符号、线号、页次到主回路、控制回路,再到 PMC 地址怎么对应回图纸上的那根线——手把手教你把一张数控机床电气原理图读明白,并顺着报警号反查故障点。
Fanuc E-Stop Circuit: G8.4, X8.4 Signals and Why the Servo Is Not Ready
Releasing the E-stop does not bring the servo back, and the control often gives no alarm number. Walks the four-layer chain: 24V safety loop, X8.4, G8.4, SA / MCC / CX4, with an X-...
FANUC Serial Spindle Alarms 749/750/751: Split by Timing, then DGN 409 and Amp Display
749, 750 and 751 are all serial communication alarms between the CNC and the spindle amplifier - not motor faults. 750 is a failed power-on handshake, 749 a dropped link after read...
FANUC 加减速时间常数与拐角减速怎么调?1620 快移 / 1622 切削进给 + 拐角过冲与圆角变钝的平衡
1620 管快速定位、1622 管切削进给,单位都是 msec,由 1610 选择指数型/直线型/铃型,1621 是铃型的 T2。本文解释为什么时间常数调大后圆角变钝、调小后拐角过冲,给「先加减速、再开 AICC」的...



















