cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
FANUC 0i-MD / 0i-MF PMC 差异对比:地址数量、机型限制与移植注意事项-CNCShare | 数控电气技术中心

FANUC 0i-MD / 0i-MF PMC 差异对比:地址数量、机型限制与移植注意事项

一句话答案:FANUC 0i-MD 与 0i-MF 同属 0i 系列但 PMC 平台不同,搭载的 PMC 容量、指令集与 X/Y 等地址范围有差异,梯形图逻辑可参考但资源不能假定一致;跨机型移植要先做地址表核对、四步走...
FANUC Alarm Code List: P/S Alarms 2032–5110 Explained (Part 5)-CNCShare | 数控电气技术中心

FANUC Alarm Code List: P/S Alarms 2032–5110 Explained (Part 5)

English reference for FANUC P/S alarm numbers 2032 to 5110: Ethernet and data server errors, P-CODE macros, peripheral axis control, sheet-metal and punch-press cycles, nibbling, a...
22天前
0658
Fanuc Backlash Compensation 1851: Measure, Convert to Detection Units, Write and Verify-CNCShare | 数控电气技术中心

Fanuc Backlash Compensation 1851: Measure, Convert to Detection Units, Write and Verify

The complete FANUC backlash compensation procedure: measure with a dial indicator at cutting feed and rapid, convert to detection units (0.020 mm becomes 20; lathe X axis times 2),...
前天
0656
HEIDENHAIN TNCremo / TNCcmd Program Transfer: Ethernet LSV2 Port 19000-CNCShare | 数控电气技术中心

HEIDENHAIN TNCremo / TNCcmd Program Transfer: Ethernet LSV2 Port 19000

TNCremo is HEIDENHAIN's official GUI transfer/backup software; TNCcmd is its command-line companion that turns connect-mkdir-put into a batch file. This covers the two roles, Ether...
7天前
06510
FANUC 伺服负载表怎么读?3111/3192 开关 + 诊断号 200–204/300 交叉验证-CNCShare | 数控电气技术中心

FANUC 伺服负载表怎么读?3111/3192 开关 + 诊断号 200–204/300 交叉验证

巡检看 POS、判定看 SV 监视、追因看诊断号。讲清实际电流(%)分段读法、峰值与持续值区分,并纠正 3111#7 被当成负载表开关、主轴诊断号混写两处错误。
SinuTrain for SINUMERIK Operate: Install, Program and Simulate on a PC-CNCShare | 数控电气技术中心

SinuTrain for SINUMERIK Operate: Install, Program and Simulate on a PC

How to install and use SinuTrain for SINUMERIK Operate on a PC: what the Siemens simulation software does, which control generations it matches, the Windows 10/11 install steps, an...
7天前
0656
How to Read a CNC Machine Electrical Schematic - Symbols, Wire Numbers, Power/Control Circuits, and Tracing an Alarm via PMC Address-CNCShare | 数控电气技术中心

How to Read a CNC Machine Electrical Schematic – Symbols, Wire Numbers, Power/Control Circuits, and Tracing an Alarm via PMC Address

A practical method for reading any CNC electrical schematic - common symbols and designations, wire/sheet numbers as coordinates, how to read the power and control circuits, and ho...
3天前
06511
共享屋电子书读者群-CNCShare | 数控电气技术中心

共享屋电子书读者群

加入共享屋电子书读者群,免费领取FANUC数控系统维修手册、PMC梯形图、报警代码大全;433位资深工程师微信群在线答疑,新手0基础也能快速上手,数控维修资料持续更新。
How to Write Mitsubishi M80 Ladder Logic into the CNC — RAM Write, ROM Copy and Checksum ERROR-CNCShare | 数控电气技术中心

How to Write Mitsubishi M80 Ladder Logic into the CNC — RAM Write, ROM Copy and Checksum ERROR

How to write the Mitsubishi M80 / M800 ladder logic (the embedded PLC sequence program) into the CNC — the GX Developer / GX Works2·3 RAM write flow, why you must 'copy to ROM', ...
3天前
06410
FANUC PMC Scan Time: Why Inputs Get Missed and Timers Fire Early-CNCShare | 数控电气技术中心

FANUC PMC Scan Time: Why Inputs Get Missed and Timers Fire Early

Buttons that sometimes do nothing, a proximity contact that flickers, timers firing early - these intermittent faults almost always trace to the PMC scan cycle. This guide explains...
5天前
0649
广告合作 / 商务合作