cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
Will Changing the HEIDENHAIN Battery Erase Your Programs? iTNC530 / TNC640 / TNC7 — What Is Lost, What Is Kept, Renata CR2450N and the Live-Swap Steps-CNCShare | 数控电气技术中心

Will Changing the HEIDENHAIN Battery Erase Your Programs? iTNC530 / TNC640 / TNC7 — What Is Lost, What Is Kept, Renata CR2450N and the Live-Swap Steps

The fear before every battery swap: will the programs be gone? On HEIDENHAIN controls like the iTNC530 the answer is no — NC programs, machine parameters, tool tables and datum of...
22天前
05011
海德汉换电池会丢程序吗?iTNC530/TNC640/TNC7 到底丢什么、留什么,附 Renata CR2450N 型号与带电更换流程-CNCShare | 数控电气技术中心

海德汉换电池会丢程序吗?iTNC530/TNC640/TNC7 到底丢什么、留什么,附 Renata CR2450N 型号与带电更换流程

换电池前最怕一句'程序会不会没'。对海德汉 iTNC530 这类控制,答案是否定的:NC 程序、机床参数、刀具表、零点偏置全在硬盘或 CF 卡里,跟那颗纽扣电池没关系。电池只保 RTC、PLC 保持位和刀补...
FANUC Spindle Amplifier Alarm Codes 01-88 (SPM/PSM) and First Checks-CNCShare | 数控电气技术中心

FANUC Spindle Amplifier Alarm Codes 01-88 (SPM/PSM) and First Checks

Reading the two digits on the spindle amp LED? This full list maps FANUC SPM alarm codes 01–88 and A/b0/C0 letter codes to plain-English meaning, first action, and how to tell whe...
前天
0457
FANUC 主轴放大器报警代码全表:SPM/PSM 两位数码管 01–88 逐条对照(含 A/b0/C0 字母码)+ 换板还是查线判定-CNCShare | 数控电气技术中心

FANUC 主轴放大器报警代码全表:SPM/PSM 两位数码管 01–88 逐条对照(含 A/b0/C0 字母码)+ 换板还是查线判定

现场拿着放大器看数码管查码,最怕两件事:把'系统 SP9012'和'放大器 12'当两个故障,或照着来路不明的码表把不该换的板子换了。本文按数码管显示的两位数字排序,逐条给中文含义、首要动作与判...
FANUC SV0381/0384/0385/0386/0387 Servo Alarms: Poor Grounding and the Linear Scale (EXT) Alarm Family-CNCShare | 数控电气技术中心

FANUC SV0381/0384/0385/0386/0387 Servo Alarms: Poor Grounding and the Linear Scale (EXT) Alarm Family

On a full-closed-loop machine SV0381/0384/0385/0386/0387 often trip alternately or keep repeating on one axis, easily misread as a broken scale or amplifier. These alarms all say '...
3天前
04713
FANUC 光栅尺报警族 SV0381/0384/0385/0386/0387:接地不良引发的全闭环外置检测器故障排查-CNCShare | 数控电气技术中心

FANUC 光栅尺报警族 SV0381/0384/0385/0386/0387:接地不良引发的全闭环外置检测器故障排查

全闭环机床上 SV0381/0384/0385/0386/0387 常交替或反复跳,容易误判成光栅尺或放大器坏了。这一族报警内容都带'(外置)',指向光栅尺等分离型检测器的反馈链路,最常见根因是接地与屏蔽没做好...
Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences-CNCShare | 数控电气技术中心

Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences

Tool measurement with a Heidenhain TT goes wrong for three recurring reasons: the cycle format does not match the control generation, the safety-zone parameter is looked for in the...
3天前
05913
海德汉 TCH PROBE 31/481 测刀循环参数对照:iTNC530 走 MP、TNC640 走 Cfg,逐齿上限 99 与 20 的分界-CNCShare | 数控电气技术中心

海德汉 TCH PROBE 31/481 测刀循环参数对照:iTNC530 走 MP、TNC640 走 Cfg,逐齿上限 99 与 20 的分界

对刀仪测刀测不准,根子多在循环格式选错代、安全区参数找错地方、TOOL.T 该预填的字段空着。本文按官方手册口径讲透 TCH PROBE 31 与 481 的两代格式差异、Q340 覆写/比较/只读三模式、Q260 安...
FANUC SERVO GUIDE: Waveform Analysis, Vibration Suppression and Rigid Tapping-CNCShare | 数控电气技术中心

FANUC SERVO GUIDE: Waveform Analysis, Vibration Suppression and Rigid Tapping

A field guide to FANUC SERVO GUIDE: what it does, which controls it supports, how to install and connect over Ethernet, and the four workflows that solve most servo problems.
前天
0826
FANUC LADDER III: Version Selection, Installation and Common Pitfalls-CNCShare | 数控电气技术中心

FANUC LADDER III: Version Selection, Installation and Common Pitfalls

A practical guide to FANUC LADDER III: which version matches which control, how to install it without the classic beginner failures, and how to get connected for online PMC monitor...
22天前
01139
广告合作 / 商务合作