FANUC ATC 报警 1010–1024 速查:机床厂自定义报警的反查方法与真实对照
加工中心刀库/ATC 报警 1010–1024 为什么在发那科原厂手册里查不到?因为它们是机床厂用 PMC 的 A 地址自定义的外部报警。本文给出报警号段划分、A 地址映射、四步反查法,以及四个真实机床厂...
FANUC Inertia Ratio: Hand Calculation, Parameter 2021, Servo Guide and AI Servo Tuning
How to calculate and measure FANUC inertia ratio: hand formulas J=Mr² and J=M(P/2π)², parameter 2021 (default 128) and the velocity-gain conversion, Servo Guide / AI Servo Tunin...
FANUC 伺服放大器 A06B 数码管报警码全表:普通码查电缆,带点码查 IPM
先按 A06B 型号分表(α SVU / α SVM / αi SVM),再用 8/9/A 过流与 8./9./A. IPM 的判别法决定先测电机线还是拆驱动;附断电三步与主轴两位码区分。
828D 设定数据 SD 和机床数据 MD 到底差在哪:号段规则、激活类型、访问等级与改错后的后果
828D 里 MD 与 SD 都存在 SRAM,但作用完全不同:MD 定义这台机器本身的物理与功能配置,改错会报警甚至撞机;SD 是操作员日常可调的运行参数,改动即时生效、风险低。本文给出官方功能手册的数...
海德汉 TNC 刀具管理怎么用?tool_p.tch 刀库表 + TOOL.T 刀具表 + L/R 补偿 + 刀具寿命一图读懂
海德汉 TNC 的刀具管理靠两张表:TOOL.T 存每把刀的长度/半径/寿命,TOOL_P.TCH 存刀库每个刀套对应哪把刀。本文讲清两张表怎么填、L/R 刀补怎么自动生效、刀具寿命怎么设,以及 tool_p.tch 读...
Fanuc Gravity-Axis Brake: Release Sequence, 24V Wiring and Diagnosing Z-Axis Drop
A Z axis that drops on E-stop or power loss is not simply a bad brake. Based on FANUC B-65162E/03-10: power-off engaged brake, power-up/down sequence, dedicated 24V circuit, BRKC, ...
Fanuc PMC R9000 System Relays Explained: Reserved Addresses, Constant ON/OFF and Pulse Timers
On a Fanuc PMC, addresses from R9000 upward are a system-reserved block you can read but must never write. This article explains why it is not a normal relay, gives a four-category...
828D 用户报警位地址速查:DB1600 顺序算法(700000–700247 / 701000–701999 扩展)
SINUMERIK 828D 用户报警位地址速查:DB1600 顺序算法与 840D DB2 分组算法的逐项对照(700247 在 828D 是 DB1600.DBX30.7,在 840D 是 DB2.DBX201.7),248 条标准报警全表推算法,701000–701...
What Is a Fanuc PMC? Ladder Logic, Addresses and Scan Time
What is a PMC in Fanuc, and how does scan time decide ladder timing?
FANUC ATC Alarms 1010–1024 — Why They Are Not in the Fanuc Manual, and How to Trace Them
Why tool changer / ATC alarms 1010–1024 cannot be found in any Fanuc manual: they are machine-tool-builder external alarms driven by PMC A addresses. This guide covers the alarm n...



















