cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
Mitsubishi M80 Tool Magazine Out-of-Order: Fix It with Tool Registration-CNCShare | 数控电气技术中心

Mitsubishi M80 Tool Magazine Out-of-Order: Fix It with Tool Registration

A scrambled tool magazine on a Mitsubishi M80 is not 'a tool loaded wrong': the recorded tool number no longer matches the physical pot. Do not copy the M70 M77/M74/M79 codes - the...
21天前
03714
数控机床内部电压分类解说-CNCShare | 数控电气技术中心

数控机床内部电压分类解说

共享屋提供数控机床内部电压的完整分级:从380V动力母线到3.3V板级电源,图解7大层级来源、负荷、保护及测试要点,助力电气工程师快速定位故障、安全维修。
FANUC 伺服调整软件 FANUC SERVO GUIDE 教程 | 下载 + 参数优化 + 振动抑制-CNCShare | 数控电气技术中心

FANUC 伺服调整软件 FANUC SERVO GUIDE 教程 | 下载 + 参数优化 + 振动抑制

FANUC SERVO GUIDE 伺服调整软件完整教程。含软件下载、伺服参数优化、振动抑制、刚性调整及故障排查。电气工程师必备高阶调试工具,支持 0i-F/0i-MF/30i 系统。FANUC SERVO GUIDE software tun...
前天
0156914
三菱 M80 梯形图怎么写进 CNC?GX Developer 写 RAM、转 ROM 与 Checksum ERROR 排查-CNCShare | 数控电气技术中心

三菱 M80 梯形图怎么写进 CNC?GX Developer 写 RAM、转 ROM 与 Checksum ERROR 排查

三菱 M80 / M800 的梯形图(内嵌 PLC 序列程序)怎么写进 CNC:GX Developer / GX Works2·3 写入内藏 RAM 的流程、为什么必须'转 ROM'固化、以及 Checksum ERROR 的根因(转换错误把出错步变 N...
Fanuc 0i-F / 0i-F Plus Function Options and How to Find Out What Your Machine Actually Has-CNCShare | 数控电气技术中心

Fanuc 0i-F / 0i-F Plus Function Options and How to Find Out What Your Machine Actually Has

The manual lists AI contour control, so why can you not use it? An operating manual describes every optional function in the series. Symbol legends, three verification paths, optio...
7天前
04714
FANUC 伺服放大器更换实操:断电放电 5 分钟、拆装顺序、电机 ID 与参数写回、换完必做的三项验证-CNCShare | 数控电气技术中心

FANUC 伺服放大器更换实操:断电放电 5 分钟、拆装顺序、电机 ID 与参数写回、换完必做的三项验证

FANUC 伺服放大器更换实操:从该不该换的决策、断电放电 5 分钟与验电挂牌、拆装顺序(先标记再拔线后拆螺丝)、电机 ID No.2020 与初始化位 No.2000#1 参数写回、FSSB 自动设定,到换完必做的...
FANUC PMC Project From Scratch: The 6-Stage Flow From Backup to Download to Verification-CNCShare | 数控电气技术中心

FANUC PMC Project From Scratch: The 6-Stage Flow From Backup to Download to Verification

A complete FANUC PMC project in six stages: site survey, full backup, address planning, safety-first logic, online download, staged verification. Plus the five things to hand over ...
10天前
04813
Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences-CNCShare | 数控电气技术中心

Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences

Tool measurement with a Heidenhain TT goes wrong for three recurring reasons: the cycle format does not match the control generation, the safety-zone parameter is looked for in the...
3天前
05913
FANUC 0i-D 系列深度解析——从硬件到生态的全景式拆解-CNCShare | 数控电气技术中心

FANUC 0i-D 系列深度解析——从硬件到生态的全景式拆解

FANUC 0i-D 硬件架构、功能包选型、αi/βi 伺服生态、高速高精技术一次看懂,附选型表 PDF,适合 1-3 年电气工程师系统提升。
FANUC 外围报警(1000/2000 段)查不到原因?A 地址→梯形图→I/O 点 四步反查法-CNCShare | 数控电气技术中心

FANUC 外围报警(1000/2000 段)查不到原因?A 地址→梯形图→I/O 点 四步反查法

FANUC 外围报警(1000/2000 段)是机床厂用 PMC 的 A 地址做的自定义报警。本文给出四步反查法:PMC 信号状态找 A 位 → 梯形图 W-搜索线圈逆推触点 → X 点按 I/O Link 分配反查端子排 → 强制...
广告合作 / 商务合作