cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
看懂PMC,其实没那么难-CNCShare | 数控电气技术中心

看懂PMC,其实没那么难

《看懂PMC程序,其实没那么难》电子书高清PDF,图解急停、润滑、四轴、倍率控制及报警文本,配套PMC仿真软件,适合数控维修与调试人员从零读懂梯形图。售价100元,付款后本页立即下载。
FANUC PMC 维修学习资料-CNCShare | 数控电气技术中心

FANUC PMC 维修学习资料

Complete FANUC PMC Ladder Programming Manual & Guide. Learn FANUC PMC programming, LADDER III software installation, address table (X/Y/G/F), and troubleshooting. Download PDF manu...
FANUC Alarm History and Operation History: Using 3106#4 OPH to Trace Intermittent Faults-CNCShare | 数控电气技术中心

FANUC Alarm History and Operation History: Using 3106#4 OPH to Trace Intermittent Faults

Intermittent faults cannot be reproduced on demand, so the only evidence is the timeline. Based on the official FANUC maintenance manual, this guide covers 3106#4 OPH, 3106#7 OHS, ...
2天前
03512
SINUMERIK 840D sl Alarm List: NCK, Cycle, HMI, SINAMICS and PLC Number Ranges-CNCShare | 数控电气技术中心

SINUMERIK 840D sl Alarm List: NCK, Cycle, HMI, SINAMICS and PLC Number Ranges

840D sl alarms use six digits. Identify the official range first, then read the cancel criterion before cycling power. Corrects two widespread range misreadings.
2天前
05811
Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers-CNCShare | 数控电气技术中心

Sinumerik F-Code Cross-Reference: F300xx / F0xxx / A3xxx Mapped to 230xxx Display Numbers

The manual calls it F30020, a 828D screen shows 230020 - one fault, two numbering systems. This table maps SINAMICS F codes to 828D/840D sl display numbers, fault meanings and firs...
2天前
04110
SINUMERIK Drive Faults Explained: F30020, F30021, F30011, F07011 and A30010 — the 230xxx Mapping, r0949 Fault Values and First Checks-CNCShare | 数控电气技术中心

SINUMERIK Drive Faults Explained: F30020, F30021, F30011, F07011 and A30010 — the 230xxx Mapping, r0949 Fault Values and First Checks

The 828D shows 230020 but the manual says F30020 - one fault, two numbering systems. This guide explains how to translate display numbers back to the manual, locate the alarm famil...
2天前
06313
海德汉光栅尺报警排查:跟随误差超标、坐标突跳、尺寸漂移三类故障的逐段诊断-CNCShare | 数控电气技术中心

海德汉光栅尺报警排查:跟随误差超标、坐标突跳、尺寸漂移三类故障的逐段诊断

海德汉光栅尺报警逐段诊断教程:跟随误差超标、坐标突跳、尺寸漂移三类现象分向定位,按尺面与读数头、电缆与接头、供电、接地与屏蔽四段依次排除,含信号幅值判读基准与劣化基线、官方清洁规范...
FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查-CNCShare | 数控电气技术中心

FANUC 报警履历 / 操作履历怎么调出来?3106#4 OPH 与间歇性故障的时间轴反查

间歇故障复现不了,只能靠「什么时候报的」串证据。本文按 FANUC 官方维修手册给出 3106#4 OPH、3106#7 OHS、3122 时标间隔与外部操作消息历史的位定义、操作履历画面调出路径,纠正网上把 #4/#...
SINUMERIK 828D 报警号分段速查表:000000–799999 分段规则与「这条报警该找谁」判定表-CNCShare | 数控电气技术中心

SINUMERIK 828D 报警号分段速查表:000000–799999 分段规则与「这条报警该找谁」判定表

828D 报警号不是随机数字:000000–199999 是 NC/HMI,200000–299999 是 SINAMICS,300000–399999 是驱动 I/O,400000–699999 是 PLC,700000+ 是机床厂自定义。本文给出完整分段表、三步判...
SINAMICS F 码怎么查?828D 上的 230020 到底是 F30020 —— F30001 / F30011 / F30021 / F07011 / A30010 逐条对照 + r0949 故障值读法 + 首选检查动作-CNCShare | 数控电气技术中心

SINAMICS F 码怎么查?828D 上的 230020 到底是 F30020 —— F30001 / F30011 / F30021 / F07011 / A30010 逐条对照 + r0949 故障值读法 + 首选检查动作

828D 屏上报 230020,手册里却是 F30020——同一故障两套编号。本页讲清怎么从屏幕显示号回到手册、四族报警先定位、F30020/F30021/F30011/F07011/A30010 逐条排错、r0949 故障值如何决定查线还...
广告合作 / 商务合作