FANUC 车螺纹乱牙 / 螺距不对怎么查?G32/G92/G76 主轴同步链路 + 一转信号 + G96 恒线速与 G50 限速设置
车螺纹乱牙不是改刀补能解决的,本质是主轴一转信号与 Z 轴每转进给的同步被破坏。本文按 FANUC 官方维修手册给出三类乱牙表现的分流方法、G32/G92/G76 的同步要求、SP9041/9042/9046/9047 报警...
Fanuc Servo Alarm Reference Chart: CNC SV Code, Amplifier 7-Segment Code and Diagnostic Number
One fault often shows both a CNC SV alarm and an amplifier seven-segment code, but FANUC publishes no universal mapping. This page explains the three code systems, verifiable numbe...
数控机床冷却 / 油路 / 排屑 / 气压 / 液压 五类报警怎么查?英文报警文本 → PMC 反馈位 → 处理动作
冷却、润滑、排屑、气压、液压五类英文报警大多不是系统报警,而是机床厂写在 PMC 里的自定义文本。本页给出五子系统横向对照:文本只是线索,真正要查的是「没就绪还是执行中受阻」,再沿报警...
Fanuc Analog Spindle Commissioning: Enable Chain 8133#5/3716#0/3717, 3730/3731 Voltage Calibration, and JA40/JA41 Wiring
An analog spindle is rarely beaten by the number of parameters. It is beaten by a wrong enable order, 3730 and 3731 swapped, or an inverted coder phase on JA41. Four stages in orde...
FANUC 对刀仪 / 测头怎么标定?5015–5018 四个接触面 + G31 / G36 / G37 + O9000 宏程序链
5015 与 5016 不是内径刀与外径刀,官方手册写的是 X 轴正负两个接触面。本页按官方附加手册讲清 5015–5018 四个基准距离、标定六步、G31 宏变量与参数号的分层、G36/G37 分工,以及宏程序编号...
Fanuc G41/G42 Interference Alarm: The 2×TNR Minimum Radial Step Rule Explained
The complete FANUC G41/G42 interference alarm (PS0041 / PS0325) guide: the 2×TNR minimum radial step rule with the 0.0156 inch / 0.0092 inch worked case, the TNR matrix, five caus...
SINUMERIK 840D sl 与 S7-1500 怎么通讯?PROFINET 设备名 + NCVAR Selector 从 PLC 读写 MD 全流程
MD 存在 840D sl 的 NC 内核里,不在 PLC 的 DB 中。本页按官方边界与现场流程分开讲:PROFINET 设备名、NCVAR Selector 六步、TIA Portal 限制、150202 的真实含义与四类备份。第三方块名与错...
FANUC Spindle Amplifier Alarm Codes 01-88 (SPM/PSM) and First Checks
Reading the two digits on the spindle amp LED? This full list maps FANUC SPM alarm codes 01–88 and A/b0/C0 letter codes to plain-English meaning, first action, and how to tell whe...
FANUC Alarm Code List: P/S Alarms 1332–1973 Explained (Part 4)
English reference for FANUC P/S alarm numbers 1332 to 1973: 3D handle feed, normal direction control, M code duplication, index table, program security, EGB, RS-232C interface, USB...
西门子 828D 模拟主轴 / 模拟轴怎么配置:MD30100–31050 参数组 + X252 接线 + MD32250/32260 量程标定
828D 接变频器 / 模拟驱动时,要把轴配成「模拟轴(模拟量给定输出)」而不是数字轴。本文给出 MD30100 / 30110 / 30120 / 30130 / 30134 与 MD30200 / 30220 / 30230 / 30240 的取值口径,X252...



















