cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
海德汉 iTNC530 / TNC620 / TNC640 / TNC7 怎么区分与迁移?参数体系 MP→Cfg、循环兼容性与程序转换清单-CNCShare | 数控电气技术中心

海德汉 iTNC530 / TNC620 / TNC640 / TNC7 怎么区分与迁移?参数体系 MP→Cfg、循环兼容性与程序转换清单

iTNC 530 用 MP 机床参数、TNC 620/640/TNC7 用 Cfg 结构化配置,这是换机与升级的第一道分水岭。本文按海德汉官方资料给四代系统定位(控制环数、用途、界面)、程序与刀具表能否直接导入、循...
Fanuc 0i-F / 0i-F Plus Function Options and How to Find Out What Your Machine Actually Has-CNCShare | 数控电气技术中心

Fanuc 0i-F / 0i-F Plus Function Options and How to Find Out What Your Machine Actually Has

The manual lists AI contour control, so why can you not use it? An operating manual describes every optional function in the series. Symbol legends, three verification paths, optio...
7天前
04714
FANUC PMC Troubleshooting: 5 Real Cases Using Signal Tracing-CNCShare | 数控电气技术中心

FANUC PMC Troubleshooting: 5 Real Cases Using Signal Tracing

Master FANUC PMC troubleshooting with 5 real cases: spindle M03 no response, ATC tool-change timeout, E-stop cannot reset, lube pump timer fault, hydraulic chuck no action. Uses a ...
22天前
0477
SINUMERIK 828D 中文手册下载(2026 最新)— 版本对应表 + 官方直链 + 下载失败怎么办-CNCShare | 数控电气技术中心

SINUMERIK 828D 中文手册下载(2026 最新)— 版本对应表 + 官方直链 + 下载失败怎么办

SINUMERIK 828D 中文手册下载导航:诊断→版本确认系统版本,手册文件名版本段命名规则,编程/调试/报警诊断/基础/扩展五类手册的官方入口与检索方法,PDF 打不开与乱码的 4 个解决办法,828D ...
FANUC SV0381/0384/0385/0386/0387 Servo Alarms: Poor Grounding and the Linear Scale (EXT) Alarm Family-CNCShare | 数控电气技术中心

FANUC SV0381/0384/0385/0386/0387 Servo Alarms: Poor Grounding and the Linear Scale (EXT) Alarm Family

On a full-closed-loop machine SV0381/0384/0385/0386/0387 often trip alternately or keep repeating on one axis, easily misread as a broken scale or amplifier. These alarms all say '...
3天前
04713
How HEIDENHAIN TNC Tool Management Works - tool_p.tch Pocket Table + TOOL.T Tool Table + L/R Compensation + Tool Life-CNCShare | 数控电气技术中心

How HEIDENHAIN TNC Tool Management Works – tool_p.tch Pocket Table + TOOL.T Tool Table + L/R Compensation + Tool Life

HEIDENHAIN TNC manages tools with two tables: TOOL.T holds each tool's length/radius/life, TOOL_P.TCH maps each magazine pocket to a tool. This guide explains both tables, how L/R ...
21天前
04712
数控机床冷却 / 油路 / 排屑 / 气压 / 液压 五类报警怎么查?英文报警文本 → PMC 反馈位 → 处理动作-CNCShare | 数控电气技术中心

数控机床冷却 / 油路 / 排屑 / 气压 / 液压 五类报警怎么查?英文报警文本 → PMC 反馈位 → 处理动作

冷却、润滑、排屑、气压、液压五类英文报警大多不是系统报警,而是机床厂写在 PMC 里的自定义文本。本页给出五子系统横向对照:文本只是线索,真正要查的是「没就绪还是执行中受阻」,再沿报警...
Fanuc Analog Spindle Commissioning: Enable Chain 8133#5/3716#0/3717, 3730/3731 Voltage Calibration, and JA40/JA41 Wiring-CNCShare | 数控电气技术中心

Fanuc Analog Spindle Commissioning: Enable Chain 8133#5/3716#0/3717, 3730/3731 Voltage Calibration, and JA40/JA41 Wiring

An analog spindle is rarely beaten by the number of parameters. It is beaten by a wrong enable order, 3730 and 3731 swapped, or an inverted coder phase on JA41. Four stages in orde...
21天前
04611
HEIDENHAIN Presets and Work Zero: PRESET.PR, CYCL DEF 247 vs CYCL DEF 7, M91/M92 and How to Set the Work Zero-CNCShare | 数控电气技术中心

HEIDENHAIN Presets and Work Zero: PRESET.PR, CYCL DEF 247 vs CYCL DEF 7, M91/M92 and How to Set the Work Zero

How to set the work zero on a HEIDENHAIN TNC: PRESET.PR table structure, row 0, CYCL DEF 247 versus CYCL DEF 7 DATUM SHIFT, why activating a preset wipes a datum shift, M91/M92 blo...
3天前
0466
FANUC 报警号 ↔ 参数号 ↔ 诊断号 三向反查总表:SV / PS / OH 段已核实锚点 + 新老两代编号体系-CNCShare | 数控电气技术中心

FANUC 报警号 ↔ 参数号 ↔ 诊断号 三向反查总表:SV / PS / OH 段已核实锚点 + 新老两代编号体系

拿到一条 FANUC 报警,下一步是什么?本页把「报警号 → 参数号 → 诊断号」三个方向的对应关系做成框架表:报警是现象,参数是设定,诊断是现场读数。SV、PS、OH 段逐条给出已核实锚点,先认清...
广告合作 / 商务合作