cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
Inductive Proximity Switches for CNC Machines: NPN vs PNP vs NAMUR and Their Roles as Hard Limits, Reference Switches and Tool Presence Sensors-CNCShare | 数控电气技术中心

Inductive Proximity Switches for CNC Machines: NPN vs PNP vs NAMUR and Their Roles as Hard Limits, Reference Switches and Tool Presence Sensors

Inductive proximity switches in three CNC roles - hard limit, reference switch and tool presence - with different selection rules for each. Covers why PNP suits new sourcing-input ...
3天前
0546
CNC Alarm Number Formats by Brand: FANUC vs SINUMERIK vs Mitsubishi vs HEIDENHAIN-CNCShare | 数控电气技术中心

CNC Alarm Number Formats by Brand: FANUC vs SINUMERIK vs Mitsubishi vs HEIDENHAIN

Before looking up what an alarm means, work out which control it came from. An identification card covering digits, prefixes and ranges, where to look on the control, which manual ...
3天前
0549
SINUMERIK 840D/828D UAFEHL Alarm: What It Means, Why the PLC Stops, and How to Localize It via DB2-CNCShare | 数控电气技术中心

SINUMERIK 840D/828D UAFEHL Alarm: What It Means, Why the PLC Stops, and How to Localize It via DB2

UAFEHL is not a specific fault — it is the SINUMERIK flag for 'a user alarm triggered the PLC stop.' Six root-cause families, a 5-step localization procedure, SF/STOP/RUN LED mean...
3天前
05412
HEIDENHAIN TNC Block Quick Reference: BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/CYCL DEF-CNCShare | 数控电气技术中心

HEIDENHAIN TNC Block Quick Reference: BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/CYCL DEF

The most-used HEIDENHAIN TNC Klartext blocks compressed onto one page - the 8-step program layout, a full block table, motion elements (R0/RL/RR, DR, I) and common M codes. For wri...
14天前
0548
Fanuc Pitch Error Compensation 3620-3624: Laser Measurement, Point Numbering and Parameter Entry-CNCShare | 数控电气技术中心

Fanuc Pitch Error Compensation 3620-3624: Laser Measurement, Point Numbering and Parameter Entry

The complete FANUC pitch error compensation procedure: cross-generation parameter table (0M 0712-0715/1000-1128 vs i-series 3620-3624 vs 16i/18i bidirectional 3605#0/3626/3627), la...
前天
05310
机床精度检验怎么做?球杆仪 ISO 230-4 与激光 ISO 230-2 判据对照-CNCShare | 数控电气技术中心

机床精度检验怎么做?球杆仪 ISO 230-4 与激光 ISO 230-2 判据对照

球杆仪做的是圆测试(ISO 230-4),激光干涉仪做的是定位精度与重复定位(ISO 230-2 / GB-T 17421.2),两者不是一套判据。本文给出标准分工、球杆仪六步作业、官方七类误差诊断项与验收结论三...
FANUC Parameter Write Protect (PWE): How to Unlock Parameters, SW0100, and the 3210/3211 vs 3202#4 NE9 Mix-Up-CNCShare | 数控电气技术中心

FANUC Parameter Write Protect (PWE): How to Unlock Parameters, SW0100, and the 3210/3211 vs 3202#4 NE9 Mix-Up

Four independent locks can stop you editing a FANUC control. This guide gives the MDI to SETTING to PWE path, explains why SW0100 is only a status message, and corrects the widespr...
7天前
05313
FANUC 急停回路怎么查?*ESP / G8.4 / X8.4 信号链 + 24V 安全链 + 主接触器 MCC 与「复位了还是没就绪」的定位顺序-CNCShare | 数控电气技术中心

FANUC 急停回路怎么查?*ESP / G8.4 / X8.4 信号链 + 24V 安全链 + 主接触器 MCC 与「复位了还是没就绪」的定位顺序

急停复位了伺服还是没就绪,先别拆按钮。按 FANUC 0i 连接手册口径拆开四层链:24V 安全链、X8.4、G8.4(*ESP)、SA 与 MCC / CX4,附按 X 位状态分支的分诊表与安全红线。
SINUMERIK 828D / 840D sl vs FANUC vs Mitsubishi M80 Parameter Cross-Reference (Aligned by Function)-CNCShare | 数控电气技术中心

SINUMERIK 828D / 840D sl vs FANUC vs Mitsubishi M80 Parameter Cross-Reference (Aligned by Function)

Three-brand parameter cross-reference: 828D/840D sl, FANUC and Mitsubishi M80 aligned by function across axis, soft limits, backlash, spindle, zero points, lube, filtering and serv...
前天
0538
FANUC 0i-Mate / 0i-D Alarm Quick Reference: Same Number, Different Meaning + FSSB 5134-5198 and Serial Spindle 749/750-CNCShare | 数控电气技术中心

FANUC 0i-Mate / 0i-D Alarm Quick Reference: Same Number, Different Meaning + FSSB 5134-5198 and Serial Spindle 749/750

FANUC 0i / 0i-Mate alarm quick reference: on the old 0 series 950 is a +24V fuse while on 0i it is a PMC system alarm (24V moved to 960); FSSB 5134-5198 and serial spindle 749/750 ...
6天前
05310
广告合作 / 商务合作