FANUC 0i-MF / 0i-MD 中文手册怎么找?10 本编号对照 + 官方获取入口
官方手册没有公开免登录直链,正确路径是随机交付资料、机床厂与 FANUC 授权渠道。本文只做版本编号对照、选书三步法与章节导航,不转载手册正文、不提供第三方打包或网盘链接。
Heidenhain TCH PROBE 31 / 481 Tool Length Measurement: Parameters, TOOL.T Fields and MP vs Cfg Differences
Tool measurement with a Heidenhain TT goes wrong for three recurring reasons: the cycle format does not match the control generation, the safety-zone parameter is looked for in the...
FANUC 0i-Mate / 0i-D 报警速查:与 0 系列含义不同的报警号 + FSSB 5134–5198 与串行主轴 749/750
FANUC 0i/0i-Mate 报警速查:950 在 0 系列是保险丝、在 0i 是 PMC 系统报警(960 才是 24V),FSSB 5134–5198 与串行主轴 749/750 速查表,401 V-READY 排查链,700/701 过热处置,0i-Mate 子...
SINUMERIK 828D Tool Management NC-PLC Interface Explained: DB4300, Three Tables and the Drum-Magazine Wrong-Tool Case
Following the 828D DB quick reference, this explains the interface logic: the NCK-tool-management-to-PLC handshake, DB4300 job/command bits, the DB9900/9901/9902 table roles, 1:1 v...
SINUMERIK 828D to S7-1200/1500: PN/PN Coupler Cyclic I/O vs S7 GET/PUT
A PN/PN Coupler exchanges data through PROFINET cyclic I/O mapping; S7 GET/PUT uses a one-sided S7 connection. Official configuration order, X1/X2 network split, MD12986, byte-exte...
海德汉 TNC 对话式编程入门:一个最小程序看懂 BEGIN/BLK FORM/TOOL CALL/L/C/CR/APPR/循环
海德汉 Klartext 对话式编程,屏幕问一句你答一句,不用背 G 代码。本文用一个 13 行能跑的最小程序,逐行讲清 BEGIN PGM、BLK FORM 毛坯、TOOL CALL 刀具、L 直线、C/CR 圆弧、R0/RL/RR 补偿、...
FANUC I/O Link Address Assignment: Group.Base.Slot, OC01I / OC02I and the 16-Byte Handwheel Rule
I/O Link address assignment is a four-part expression of group, base, slot and module byte count. Module byte counts, why a handwheel needs 16 bytes, I/O Link vs I/O Link i, and a ...
SINUMERIK 828D G290 G291 怎么切?DIN 写法与 ISO 写法逐行对照
G290 激活西门子 NC 编程语言,G291 激活 ISO 方言;两者必须单独成段,同段禁止混写。本页给出程序头、换刀、主轴、轮廓、循环的逐行对照,并用西门子官方手册纠正“模式可互相识别”的真正含...
FANUC 16i / 18i / 21i / 30i / 31i Identification: Model Reading, Axis Counts and Spare-Part Selection
A control in the shop says only '18i' on the panel - which generation, how many axes, and can spares be swapped? Official B-63002EN / B-63522EN axis totals include loader axes and ...
三菱 M80 刀库乱刀速查表:现象·原因·先查 + T 登录四个位置 + R 寄存器
一页看完三菱 M80 刀库乱刀:按现象对号入座,主轴同步、T 登录四个位置、刀库刀具数据与刀具寿命的 R 寄存器地址一次列清。适合现场贴着机台用。



















